Hi folks,
I currently have some cheap Zigbee hub and some Amazon Alexas running my smart home which mostly consists of Zigbee power strips and Zigbee battery powered switches.
It all worked OK originally, but now whenever I press a Zigbee switch the light in the corresponding plug switches on then immediately off again.
If I ask Alexa to turn the light on it works fine. Likewise if I switch it on from my phone.
Any ideas what the issue could be?
I've tried unplugging the hub a number of times but that doesn't seem to fix it.
I was thinking about getting a Homey Pro 2023 to speed things up (tmas the Zigbee hub seems to be really slow now as well, for some reason) but I'm not sure about that either.
Any suggestions greatly appreciated!
Hey guys...
We are replacing the heat pump and furnace this week and I will also need to replace my nest thermostat at the same time 'cause Nest is ending the cloud thing end of the month.
Anyway, I'm looking to use the
That's what the heat pump installer recommend BUT, using Nest I was also using it to control the home humidifier using a single wire connected to nest... but no low voltage thermostat is able to do that, I checked all of them...
So I need some help on how I can do that, to connect the home humidifier using zwave also....
Hi
We are looking for a solution where we can detect presence of a «thing» (people , car , dog, cat, and more..
We need:
fast detections, 1-3 seconds in range from 0 to 20 m from «base» fysical «client» , chip , transmitter , unit. base , receiver placed at a door, gate, house, etc uniq Identifying wirelessThe client:
no need for pressing any thing (no buttons) battery , hoply 2-5 years battery time.Have someone done anything like this?
What technologi will be best?
Hey everyone, I'm currently working on developing a bed sensor that can detect when you're out of bed. It could be used to trigger other smart home gadgets, like lights or blinds, temperature etc.
The sensors are placed under the legs of your bed post. Should look and feel like "smart furniture pads" with size 2 inches in diameter and 1/4 inch thick.
Before we go any further, I'd love to get your thoughts on this - would a bed sensor like this be something you'd find useful? We're still in the early stages of development, so any feedback you have would be greatly appreciated. Thanks in advance!
@DesT, fenced code blocks display differently after the upgrade.
abc defThe above should display as abc and def on two separate lines. This works. But this fails:
verbose: true config: data: "auto"The above should display as three lines, verbose: true, config: and data: "auto", but this fails. In order to make it display properly, I now have to open the fenced code block with ```text (specify language, generic text). This displays without highlighting. The words yml and yaml (and the all-caps versions) don't seem to be recognized. I can also use js to get JavaScript highlighting, but this isn't great for YAML. Here's the same block with the language (text) specifier added (no other changes):
verbose: true config: data: "auto"Sure, we can start adding language specifiers to our new posts, but I suspect if we start digging around old posts, we're going to find a lot of broken display of the fenced code blocks (plain ``` at the start with no language specifier) in the thousands of old posts in these forums, upon which people still rely for answers and information.
Log file snippets also get similarly brutalized:
[###BUILDVERSION###]2023-04-26T19:41:51.683Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs added file logger to zwavejs.log [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_device_cfg, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_mfg_spec, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_device_ver, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_values, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.837Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs connecting to ws://192.168.0.10:3000 [###BUILDVERSION###]2023-04-26T19:41:51.874Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs connected [###BUILDVERSION###]2023-04-26T19:41:51.874Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs sending connection initialization [###BUILDVERSION###]2023-04-26T19:41:51.931Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs greeting from server: [Object]{ "type": "version", "driverVersion": "10.16.0", "serverVersion": "1.28.0", "homeId": 3631280043, "minSchemaVersion": 0, "maxSchemaVersion": 28 } [###BUILDVERSION###]2023-04-26T19:41:51.932Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs performing initial inventory [###BUILDVERSION###]2023-04-26T19:41:52.325Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs manufacturer-specific data for 134 (AEON Labs) from package ver 22315.1 [###BUILDVERSION###]2023-04-26T19:41:52.328Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs configuring node 1 endpoint 0 (entity "1-0") [###BUILDVERSION###]2023-04-26T19:41:52.339Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs manufacturer-specific data for 543 (Elexa Consumer Products Inc.)I think this is going to be a problem. Is there a way in NodeBB to configure the default language for fenced code block markdown for the entire forum so that these display more as they did before the upgrade?
EDIT: Examples below of old posts with corrupt formatting now:
https://smarthome.community/topic/1101/dynamic-groups-controller-filter-expressions
https://smarthome.community/post/11362
This last old post is interesting, because the first block displays incorrectly, but the second block is OK. In playing around, there seem to be triggering character sequences, suggesting that the markdown processor is trying to "guess" the language but not getting it right, perhaps:
Hi guys,
we are doing a survey in IT privacy and security and we want to analyze the user perception of privacy concerns in smart homes. It will only take 5-10 min to fill out the survey 🙂
i would be very thankful if you could take part and help us to get as many responses as possible.
Thank you!
Can anyone help with the MIOS UI5 weblink? Not the getvera one.
Still running UI5 on a couple of sensors & lights and need to tweak PLEG but for the life of me I can't remember the link to tunnel back to the trusty machine....
The wifi on my router is turned off, and wifi around the house is provided using a mesh - 3 units altogether (one connected directly to the router) that are spread around the house.
I would like to start automating certain tasks around the house and intend to try adding a few smart sockets to my setup.
The mesh system I have supports both 2.4GHz and 5GHz, and does not provide me with the option to control them - i.e. turn one or both on/off, give each a different SSID, etc.
The devices I wish to purchase/use only support 2.4GHz.
Will turning the mesh units off and temporarily turning the 2.4GHz wifi on the router to allow me to set them up be enough? Will I then be able to return to my usual setup and everything will work as it should?
Many thanks in advance
ChatGPT samples:
Me:
Tell me about an iot program called openLuup.
It:
OpenLuup is an open source home automation system that is built on the VeraLuup platform. It is designed to be easy to install and configure, and provides users with a powerful and versatile way to control their home automation devices. OpenLuup offers a wide range of features, including support for many popular home automation devices, scheduling, scripting, and integration with other services. OpenLuup is designed to be customizable, allowing users to create their own home automation systems. It is an excellent choice for those looking to create their own home automation system without spending a lot of money.
Me:
Write an iot program using openLuup.
It:
--openLuup IoT Program-- -- Initialize Variables -- local device_id = "MyHomeDevice" local temperature_sensor_id = "MyTemperatureSensor" local temperature_threshold = 75 -- Create Devices -- luup.create_device("OpenLuup Temperature Sensor", 0, device_id, "D_GenericSensor1.xml", "I_GenericSensor1.xml", "S_TemperatureSensor1.xml", "") luup.variable_set("urn:upnp-org:serviceId:TemperatureSensor1", "CurrentTemperature", 0, device_id) -- Start Timer -- luup.call_delay("check_temperature", 10, "", false) --Function to Check Temperature-- function check_temperature() local current_temperature = luup.variable_get(temperature_sensor_id, "CurrentTemperature", 0) --Check Temperature Threshold-- if current_temperature >= temperature_threshold then --Send Alert-- luup.call_action("urn:micasaverde-com:serviceId:HomeAutomationGateway1", "SendTextMessage", {PhoneNumber="1234567890", Message="ALERT! Temperature exceeded threshold!"}, 0) end --Reset Timer-- luup.call_delay("check_temperature", 10, "", false) endMe:
Write an iot program using openLuup.
It:
Write an iot program using openLuup. -- openLuup IOT Program -- -- Variables local lampState = false local lampTime = 0 -- Functions function lampTimer() if lampTime > 0 then lampTime = lampTime - 1 if lampTime == 0 then luup.variable_set('urn:upnp-org:serviceId:SwitchPower1', 'Status', 0, lampDeviceID) lampState = false end end end -- Setup luup.call_delay('lampTimer', 60, 0) -- Main Loop while true do -- Check for motion if luup.variable_get('urn:micasaverde-com:serviceId:MotionSensor1', 'Tripped', motionSensorDeviceID) == '1' then if not lampState then luup.variable_set('urn:upnp-org:serviceId:SwitchPower1', 'Status', 1, lampDeviceID) lampState = true -- Set lamp timer to 5 minutes lampTime = 300 end end luup.sleep(1) endWhat??
luup.sleep(1)Not good - looks like I still have some semblance of a job to fulfill.
Me:
An iot program called openLuup was written by akbooer. Who is akbooer?
It: (note: answer redacted and as I understand it, also incorrect re: AltUI):
akbooer is the pseudonym of the software developer and home automation enthusiast. He is the creator of the openLuup home automation software, which is an open-source version of the Vera home automation system. He is also the creator of the AltUI graphical user interface for openLuup.
Me:
Who created of the AltUI graphical user interface for openLuup.
and
Me:
Who created of the AltUI graphical user interface for the home automation system Vera.
Names two different people - mmmm.
Regardless very impressive - give it a few more years.
...which I'd like to do. I know I go about these things all wrong (namely think of something I'd like to do, then try and work out what I need to know) but that's me 🙂
Just looking for some pointers on what I should google for really:
What I'd like is to provide a selection of (basically two word) phases which I can select from randomly (or even pseudo randomly) and pass to Alexa to be spoken. There are 10 such phrases only.
So what should I be reading up on to get me started?
TIA for any guidance
C
Hi,
I am a student and recently i am working on smart home project and writing a seminar paper about the way users handle and manage IoT devices. I you have 3 min, please fill below survey. Its really short.
Thank you in advance, I really appreciate everyone's help.
For what it's worth, I've been putting the finishing touches on a much-updated version of my DP Apps spreadsheet -- specifically intended for HE users, at least for now -- and invite you all to take a gander http://bit.ly/hedb23 at the PDF one-page version.
Corrections and edits welcome (esp. for the HOMEKIT column, just added yesterday)! Thanks in advance, especially because I'm not a big dashboard user myself, but somehow accepted this role as "keeper of the list" as it were.
Hello guys,
I would like to achieve two different things with lights, but I am not sure it could be done. I am starting with smart things, and I am far from any electrician knowledge, wo any help is really appreciated.
I have dumb switches in my hall, controlled from 3 places. I understood that installing one smart module before first switch will make them "hybrid", both smart controlled and dumb controlled.
I would like to buy ceiling light with two bulb sockets. What I would like to achieve is I would like to have one bulb for normal daily usage (lets say cold white full brightness), and second for night time (aprox from 10pm till morning) with some red/orange - minimum brightness.
So question are:
Is there a way to keep both bulbs turning-on separated? So only one will be on during day, and then only second during night?
And could that be done with pressing dumb switch? What would I need to achieve it? (maybe another module into the ceiling lights)
Thank you in advance
OT: Universal Remote
-
You lot are more likely to have a view than most I know. Our much used Logitech Harmony is (not so) slowly dying.
And Logitech have discontinued the entire line.
And no one else appears to be making something similar.
Was going for a Sofabaton X1, but no numeric keypad. Sofabaton U1, but no favourites.
Anyone got suggestions?
Needs to have those features, oh and not be only a phone app.....C
-
This may not be super helpful… but to avoid this exact situation I am stocking up on Logitech harmony devices that are being sold second hand. I haven’t found a single universal remote that comes close to Logitech Harmony line up. Maybe try your local marketplace?
-
@Pabla No it's not a bad idea. Just not keen on buying one that might be in the same condition. Prices have gone bonkers as well
There's the other issue that Logitech will eventually stop making the software, and then your stock may well be little more than paperweights
C
-
@CatmanV2 said in OT: Universal Remote:
There's the other issue that Logitech will eventually stop making the software, and then your stock may well be little more than paperweights
C
I don't use their cloud thankfully and have them locally connected with HA so I hope they don't completely brick these devices
-
Since I have a bunch of Logitechs as well, I backed this on kickstarter. https://www.kickstarter.com/projects/flirc/the-skip-1s-universal-remote-control-by-flirc/description Should be shipping soon I think. This is their commercial webpage: https://flirc.tv/products/skip1s-remote?variant=43489094729960
-
@CatmanV2 said in OT: Universal Remote:
Bring back the Pronto!
Probably not quite what you're after but there is a Vera-virtual-pronto-remote plugin.
Just need some sort of IR transmitter(s).
I use a couple of minimotes to turn on/off the source equipment, operate volume, pause, mute etc. You can use luup code to set up complex sequences.
-
I'm mainly using my Harmony Remote via the hub (so, voice commands via Alexa and scene) and the remote is in fact in a drawer since we moved to the new house (5 year and a half). Since I've added the SkyQ box in my setup, the SkyQ remote is enough (they have apps directly integrated into the box, so no need to use the TV remote anyway and no need to switch outputs). In other rooms we have Fire TVs, so we're already covered. Today I'm just using the hub when we (rarely) watch live TV on Sky in other rooms (thanks to a distribution system mapping HDMI outputs to DVB-T channels) and to automatically turn off TV when leaving the house (ie: kids stopped playing at xbox seconds before we're heading out and forgetting to turn off TV - I have TV on when turning on xbox, but I prefer to turn if off). I have spare IR emitters that someday I'll repurpose. I'm just using command from MSR to home assistant to send codes and I'm not using presets anyway.
I guess the future is in no-remotes setups - even TV manufacturers have started to remove buttons from their remotes
-
@CatmanV2 I'm not that old
but yes, kids (well, I'm still calling them kids even if they are 23 and 15
) are watching TV with me just for football (and there I mean the real football played with foot
) and the trend is probably more about casting to your TV and using your devices as the remote than needing a remote.
Looking at my previous setup (and the one I started in this house), I have completely removed scene controllers (I still have one and that's used only by my wife) and remotes and have more automations/voice commands in place.
-
@therealdb we are that old
Why one earth would I want to cast from my Tivo to my TV when there is already a perfectly good cable? And why would I want to open an app to chose channel on Tivo?
Have exactly this issue with my Streamer (until I got it upgraded to take a remote)
Listening to music
Phone rings
Can't hear caller because of music
Need to come out of call, open app, turn down volume, return to call.
Just (and I will sound like a luddite) cannot see this is as a great experience
C -
@CatmanV2 oh, we're definitely not automated/integrated everything, and things are a little bit weird ATM. that's why I told my wife we will build a new house in 10 years, so I could start from scratch and really choose the best tech after all these esperiments (LOL) and I hope than in 10 years (I'm looking at your, matter) interoperability will definitely improve things like the one you mentioned.
-
C CatmanV2 has marked this topic as solved on
-
Just to close this off, I managed to get a Harmony Elite and Hub from ebay. Lightly used at a reasonable price.
God knows why they are pulling out of the market. First impressions is it's an ace bit of gear. Didn't realise quite what the hub could do and am thinking of getting another to replace my Broadlink in the cinema.Thanks, all
C