openweather plugin ?

[ArcherS]

@akbooer I have "AsyncPoll" true on the Zway Bridge, I assume that means that it is in asynchronuous mode? Or should I check something else?

No, I have yet to install cjson. This was actually intentional since I wanted to test it without this first and see if it works. On my main OpenLuup server that has experienced crashes I have cjson installed so I wanted to test without cjson first. But I should test this later on and see what happens to the cpu load.
Regarding cpu load it has not gone up that much when comparing running one Tasmota vs running seven which is promising.

I am not sure what message that causes the error, do you have any ideas what I should look for in the log or elsewhere? It mentions "TasmotaBridge.Lua:188 table index is nil" in all errors for the devices.

The errors always says:

2021-04-14 21:19:10.214   openLuup.context_switch::  ERROR: [dev #14] openLuup/L_TasmotaBridge.lua:188: table index is nil

2021-04-14 21:19:10.214   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/TasmotaTest/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil

and it seems to cycle through my Tasmota devices reporting the same two rows but for each device:

2021-04-14 21:35:10.064   openLuup.context_switch::  ERROR: [dev #14] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 21:35:10.065   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/TasmotaTest/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil
...
2021-04-14 21:35:42.864   openLuup.context_switch::  ERROR: [dev #14] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 21:35:42.865   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/TasmotaUterum/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil
...
2021-04-14 21:35:44.637   openLuup.context_switch::  ERROR: [dev #14] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 21:35:44.637   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/TasmotaCO2An/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil
...
2021-04-14 21:35:44.844   openLuup.context_switch::  ERROR: [dev #14] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 21:35:44.844   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/TasmotaCO2Ax/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil

Yes I agree, it seems to be going well.

No, I think it is quite good the way it is, creating Virtual Sensors and then linking them to the devices/variables is very easy. It only takes a few minutes to add a new Tasmota device from scratch without any coding at all.
In fact I think it is better this way since typically you do not want all of the reported values as a child device, e.g. you do not want "Dew point" or "Time", the useless MHZ19B temperature etc. This way you can select only what you want, not getting OpenLuup cluttered by a lot of "useless" child devices.

[Elcid]

@akbooer, I have bridged the 2 brokers but not seeing any Tasmota bridge I see the mosquitto bridge in the openluup log no errors. My topics are tasmota/stat/devicename/POWER The devices are sonoff mini's flashed with tasmota-lite.bin. Any ideas?

[akbooer]

@elcid said in openLuup: Tasmota MQTT Bridge:

My topics are tasmota/stat/devicename/POWER

So, at the moment, I have only subscribed to tele/#, so that's why you're not seeing anything.

I can make this configurable, but what does a message look like with this topic?

[Elcid]

@akbooer
Ask the device for status

cmnd/tasmota_switch/Power ←     // an empty message/payload sends a status query
    ↳ stat/tasmota_switch/RESULT → {"POWER":"OFF"}  
    ↳ stat/tasmota_switch/POWER → OFF
We can see that the switch (devices relay) is turned off.
Send a command to toggle the relay~

cmnd/tasmota_switch/Power ← "TOGGLE"
    ↳ // Power for relay 1 is toggled
    ↳ stat/tasmota_switch/RESULT → {"POWER":"ON"}  
        ↳ stat/tasmota_switch/POWER → ON

I have appended th tasmota at the start of the topic in my tasmota device settings.

[akbooer]

ATM the bridge doesn't solicit any response from the devices. Indeed, it would have to discover them first in order to do so. So at this time, if the device does not sent regular tele/ updates, then it won't be seen. This is early days for the bridge.

[Elcid]

@akbooer
There is a tele topic. Sorry about the image as the App would not let me copy the text.
and there is also a -
tasmota/tele/name/LWT with message "Online"

[akbooer]

OK, well that will work if I add configuration for your optional ‘Tasmota’ prefix.

[Elcid]

I added the prefix for future use so i could group devices by type (sensor/switch/dimmer/etc) as i will filter topics by type of device i want to subscribe to. So it would be nice to have a list of prefixes, if it is possible.

[Buxton]

@akbooer Good start on my end. Here's a pic of one device that shows three Bluetooth temp/humidity sensors (LYWSD...) that connect to a Tasmota relay:

You may need to decode a layer deeper for the "table" entries....

I do have a bunch of error messages in the log, but I will have to get into that on the weekend as I'm currently buried with work work....

Here's a snippet though:

2021-04-14 20:11:13.634   openLuup.context_switch::  ERROR: [dev #262] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 20:11:13.634   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/BLE : openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 20:11:14.044   openLuup.server:: request completed (1490 bytes, 1 chunks, 1280 ms) tcp{client}: 0x5619338130b8
2021-04-14 20:11:14.642   openLuup.context_switch::  ERROR: [dev #262] openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 20:11:14.642   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/STATE : openLuup/L_TasmotaBridge.lua:188: table index is nil
2021-04-14 20:11:14.662   openLuup.context_switch::  ERROR: [dev #0] attempt to call a string value
2021-04-14 20:11:14.663   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/SENSOR : attempt to call a string value
2021-04-14 20:11:14.701   openLuup.context_switch::  ERROR: [dev #262] openLuup/L_TasmotaBridge.lua:188: table index is nil

[therealdb]

Ok, I've added support for command based on MQTT in version 3.0-beta1.

Variable updated on messages coming soon. Feedback much appreciated!

GitHub - dbochicchio/vera-VirtualDevices: Virtual HTTP Devices plug-in for Vera and openLuup

Virtual HTTP Devices plug-in for Vera and openLuup - dbochicchio/vera-VirtualDevices

[Buxton]

@akbooer I did some debug on the error messages above and came up with the following. I placed some debug entries in the "L_TasmotaBridge.lua" to try to see what was causing the errors. First the code: under function _G.Tasmota_MQTT_Handler (topic, message)

  local myMessage = ""
  
  if message == nil then 
     myMessage = "Message is null" 
  else
	if message == "" then
	 myMessage = "Message is empty" 
	else
	 myMessage = message 
	end
  end
  
  _log ("JSON error info " .. myMessage)

Which produced the following log errors and their context:

2021-04-16 20:48:01.335   openLuup.io.server:: MQTT:1882 connection from 10.17.2.28 tcp{client}: 0x55fac42317b8
2021-04-16 20:48:01.355   luup.tasmota:262: JSON error info Online
2021-04-16 20:48:01.356   luup.tasmota:262: JSON error: ?
2021-04-16 20:48:01.366   luup.tasmota:262: JSON error info Message is empty
2021-04-16 20:48:01.367   luup.tasmota:262: JSON error: ?
2021-04-16 20:48:01.423   openLuup.mqtt:: BedroomTV SUBSCRIBE to cmnd/power_BedroomTV/# tcp{client}: 0x55fac42317b8
2021-04-16 20:48:01.432   openLuup.mqtt:: BedroomTV SUBSCRIBE to cmnd/tasmotas/# tcp{client}: 0x55fac42317b8
2021-04-16 20:48:01.433   openLuup.mqtt:: BedroomTV SUBSCRIBE to cmnd/BedroomTV_fb/# tcp{client}: 0x55fac42317b8

[Buxton]

@akbooer Then further down the log file I was getting errors in the "function init_device (altid, info)" function. Error code is:

	local myaltid = ""
	local myinfo = ""
	
	if altid == nil then
		myaltid = "altid is null"
		else
		myaltid = altid
	end
	
	if info == nil then
		myinfo = "info is null"
		else
		if info == " " then
			myinfo = "info is empty"
		else
			myinfo = unpack(info)
		end
	end


	_log ("Find info " ..  myinfo )
	_log ("Find altid " .. myaltid )

  local dno = luup.openLuup.find_device {altid = altid} 
                or 
                  create_device (altid, info)
 
	_log ("Find DNO " .. dno)

Which yields:

2021-04-16 21:37:06.773   openLuup.io.server:: MQTT:1882 connection closed  tcp{client}: 0x556c246bb0f8
2021-04-16 21:37:06.773   openLuup.mqtt:: RECEIVE ERROR: closed tcp{client}: 0x556c246bb0f8
2021-04-16 21:37:06.815   luup.io.incoming:: bytes received: 51, status: OK tcp{client}: 0x556c24620fb8
2021-04-16 21:37:09.516   luup.tasmota:262: JSON error info {"Time":"2021-04-17T05:37:09","Uptime":"0T02:24:57","UptimeSec":8697,"Heap":125,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":13,"POWER1":"OFF","POWER2":"OFF","Wifi":{"AP":1,"SSId":"CD","BSSId":"FE:9F:DB:F5:A0:11","Channel":1,"RSSI":94,"Signal":-53,"LinkCount":1,"Downtime":"0T00:00:06"}}
2021-04-16 21:37:09.517   luup.tasmota:262: Find info info is null
2021-04-16 21:37:09.517   luup.tasmota:262: Find altid altid is null
2021-04-16 21:37:09.517   luup.tasmota:262: Find DNO 1
2021-04-16 21:37:09.518   openLuup.context_switch::  ERROR: [dev #262] openLuup/L_TasmotaBridge.lua:215: table index is nil
2021-04-16 21:37:09.518   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/STATE : openLuup/L_TasmotaBridge.lua:215: table index is nil
2021-04-16 21:37:09.605   openLuup.context_switch::  ERROR: [dev #0] attempt to call a string value
2021-04-16 21:37:09.605   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/SENSOR : attempt to call a string value
2021-04-16 21:37:09.605   luup.tasmota:262: JSON error info {"Time":"2021-04-17T05:37:09","Switch1":"ON","Switch2":"ON","ENERGY":{"TotalStartTime":"2021-04-04T05:29:11","Total":0.000,"Yesterday":0.000,"Today":0.000,"Period":0,"Power":[0,0],"ApparentPower":[0,0],"ReactivePower":[0,0],"Factor":[0.00,0.00],"Frequency":60,"Voltage":121,"Current":[0.000,0.000]}}
2021-04-16 21:37:09.606   luup.tasmota:262: Find info info is null
2021-04-16 21:37:09.606   luup.tasmota:262: Find altid power_BedroomTV
2021-04-16 21:37:09.606   luup.tasmota:262: Find DNO 30001
2021-04-16 21:37:09.618   luup.tasmota:262: JSON error info {"Time":"2021-04-17T05:37:09","BLEDevices":{"total":3,"A4C138EB4F4F":{"i":0,"r":-73},"A4C13838EB2E":{"i":1,"r":-87},"A4C138A59E0C":{"i":2,"r":-92}}}
2021-04-16 21:37:09.619   luup.tasmota:262: Find info info is null
2021-04-16 21:37:09.619   luup.tasmota:262: Find altid altid is null
2021-04-16 21:37:09.619   luup.tasmota:262: Find DNO 1
2021-04-16 21:37:09.619   openLuup.context_switch::  ERROR: [dev #262] openLuup/L_TasmotaBridge.lua:215: table index is nil
2021-04-16 21:37:09.619   openLuup.mqtt:: ERROR publishing application message for mqtt:tele/power_BedroomTV/BLE : openLuup/L_TasmotaBridge.lua:215: table index is nil
2021-04-16 21:37:09.620   luup.tasmota:262: JSON error info {"Time":"2021-04-17T05:37:09","BLE":{"scans":483,"adverts":23232,"devices":3,"resets":0}}
2021-04-16 21:37:09.620   luup.tasmota:262: Find info info is null
2021-04-16 21:37:09.620   luup.tasmota:262: Find altid altid is null
2021-04-16 21:37:09.620   luup.tasmota:262: Find DNO 1

Hope that's of some use.

[Buxton]

@buxton In the above, I'm seeing an extra closing right hand bracket in the JSON string.

[therealdb]

And I've also added handlers to get status from a generic MQTT message. It's done on lights, dimmers, roller shutters and rgb/rgbw.

Just use the format topic/=/payload, where * for payload means "pass the value to the variable".

Color and white temp are supported, but I'll need to write a converter (or link to the existing one). If anyone is still interested, I could port it to alarm, heaters, door locks and sensors.

[akbooer]

@Elcid

The latest development version v21.4.17 has added and additional subscription to the tasmota/tele/# topic. I will make it configurable later.

@Buxton

I've refactored the bridge a bit, but haven't yet addressed the nested table issue... don't know if this has fixed any of the other errors you've seen, but I didn't do anything explicitly to address those. Still very much work in progress.

[Elcid]

Has installed tasmota bridge and the child devices have been added with the following varaiables

LastUpdate	
17/04/2021, 12:43:57
Switch1	
OFF
Time	
2021-04-17T12:43:57
tasmota/tele	
{"Time":"2021-04-17T12:43:57","Switch1":"OFF"}

[ArcherS]

I have now updated to v21.4.17 and also installed cjson.

The cpu load on my test Pi went down from 10.5% to 4-4.5%, so that is a good step better.

The server has been running with my Zway bridge with 64 zNodes and 165 vDevs and five Tasmota devices.
Data this morning after 2.5 days run time:

I have added one more Tasmota device, in total 6 are now pushing data over Mqtt to OpenLuup.

@akbooer what is changed in v21.4.17, I could not see any changes to be honest.

What I did notice however was that the old error messages I posted above have disappeared. I will see if I get any new, so far I have not seen any.

[akbooer]

@archers said in openLuup: Tasmota MQTT Bridge:

what is changed in v21.4.17

Well, I think you answered your own question...

@archers said in openLuup: Tasmota MQTT Bridge:

the old error messages I posted above have disappeared

[akbooer]

@buxton said in openLuup: Tasmota MQTT Bridge:

You may need to decode a layer deeper for the "table" entries....

Version 21.4.17c does just that (I hope.)

Would be interesting in seeing the variables which result...

[Elcid]

Just reporting that the variables in the tasmota devices are not updating correctly

tasmota/tele	
{"Time":"2021-04-17T19:28:59","Switch1":"ON"}

The time stamp updates, but not the value of Switch1.
[edit] after deleteing the 4 devices and reloading luup I found these errors in log

2021-04-17 19:59:39.142   openLuup.server:: GET /data_request?id=lu_status2&output_format=json&DataVersion=685929357&Timeout=60&MinimumDelay=1500&_=1618685858944 HTTP/1.1 tcp{client}: 0xff56978
2021-04-17 19:59:39.145   openLuup.mqtt:: localhost.bridge-01 SUBSCRIBE to # tcp{client}: 0xff593e0
2021-04-17 19:59:39.147   luup.tasmota:47: JSON error: Expected value but found invalid token at character 1
2021-04-17 19:59:39.148   luup.tasmota:47: JSON error: Expected value but found invalid token at character 1
2021-04-17 19:59:39.153   luup.tasmota:47: JSON error: Expected value but found invalid token at character 1
2021-04-17 19:59:39.154   luup.tasmota:47: JSON error: Expected value but found invalid token at character 1