Use case:
When performing home maintenance, such as air conditioning, I want all rules involving air conditioning to be disabled.
To do this, to day, I have a virtual switch that I placed within all rules involving air conditioning, meaning that if I turn it off, none of them work.
Then another situation: the water pump system and garden irrigation, another switch.
In short, I had to create several virtual switches in Hubitat to disable rules in MSR.
Unfortunately, however, I was unable to cover all scenarios, so I wondered if it would be possible for MSR to support a virtual MSR switch, which, when configured in the reactor settings, would function as a general on/off switch for MSR.
If it is configured and turned off, the entire rules and actions in MSR stops working, except for the status change reading process, specifically for this switch, which, when turned on, would restart the MSR.
Would it be possible to do something like this? Any recommendations from the experts?
@toggledbits, not sure if this is a feature request or I'm using the search tool wrong. You have a "Search for rule" in the Rules Set tab in MSR. It works nicely to find a rule and bring up said rule, but can it/could it be used for as a "where used?" global search? For instance, I have a fairly large set of rules, divided up into 10 different rulesets. There's easily a hundred individual rules, and many of the rules have Rule State triggers, which of course refer to other rules. Amongst my troubleshooting today, I came across what may have been a duplicate or troubleshooting attempt, but I can't tell if it's actually used as a Rule State in another rule without opening each rule that I suspect it may be a part of.
Thanks.
I'm running MSR build 25139 on Docker, using MQTT controller 24293, and everything working as expected. But if I try to upgrade to MQTTController build 25139, I'm getting the following errors on MSR UI:
An Entity Attribute condition in "Lay-Z-Spa auto heating off" (Terrace) failed because the referenced entity "Lay-Z-Spa States" (mqtt>layzspa_states) does not have attribute value_sensor.god
Last 11:20:37
An Entity Attribute condition in "Lay-Z-Spa auto heating off" (Terrace) failed because the referenced entity "Lay-Z-Spa States" (mqtt>layzspa_states) does not have attribute temperature_sensor.green
Last 11:20:37
An Entity Attribute condition in "Lay-Z-Spa filter pump auto off" (Terrace) failed because the referenced entity "Lay-Z-Spa States" (mqtt>layzspa_states) does not have attribute temperature_sensor.red
Last 11:20:37
An Entity Attribute condition in "Lay-Z-Spa filter pump auto run" (Terrace) failed because the referenced entity "Lay-Z-Spa States" (mqtt>layzspa_states) does not have attribute value_sensor.pump
Last 11:20:37
An Entity Attribute condition in "Lay-Z-Spa watchdog" (Terrace) failed because the referenced entity "Lay-Z-Spa States" (mqtt>layzspa_states) does not have attribute value_sensor.status
Last 11:20:37
My MQTT configuration (local_mqtt_devices.yaml) for the related entity is:
layzspa_message:
type: ValueSensor
capabilities: ["temperature_sensor", "value_sensor", "power_sensor"]
primary_attribute: power_sensor.value
events:
"layzspa/message":
"power_sensor.value":
json_payload: true
if_expr: '! isnull( payload?.PWR )'
expr: "float(payload.PWR)"
"value_sensor.air":
json_payload: true
if_expr: '! isnull( payload?.AIR )'
expr: "float(payload.AIR)"
"value_sensor.pump":
json_payload: true
if_expr: '! isnull( payload?.FLT )'
expr: "float(payload.FLT)"
"value_sensor.god":
json_payload: true
if_expr: '! isnull( payload?.GOD )'
expr: "float(payload.GOD)"
"value_sensor.lock":
json_payload: true
if_expr: '! isnull( payload?.LCK )'
expr: "float(payload.LCK)"
"value_sensor.unit":
json_payload: true
if_expr: '! isnull( payload?.UNT )'
expr: "float(payload.UNT)"
"value_sensor.error":
json_payload: true
if_expr: '! isnull( payload?.ERR )'
expr: "float(payload.ERR)"
"temperature_sensor.green":
json_payload: true
if_expr: '! isnull( payload?.GRN )'
expr: "float(payload.GRN)"
"temperature_sensor.red":
json_payload: true
if_expr: '! isnull( payload?.RED )'
expr: "float(payload.RED)"
"temperature_sensor.target":
json_payload: true
if_expr: '! isnull( payload?.TGT )'
expr: "float(payload.TGT)"
"temperature_sensor.value":
json_payload: true
if_expr: '! isnull( payload?.TMP )'
expr: "float(payload.TMP)"
"temperature_sensor.virtual":
json_payload: true
if_expr: '! isnull( payload?.VTM )'
expr: "round(float(payload.VTM), 1)"
"temperature_sensor.ambient":
json_payload: true
if_expr: '! isnull( payload?.AMB )'
expr: "float(payload.AMB)"
"layzspa/Status":
"value_sensor.status":
if_expr: '! isnull( payload )'
expr: "payload"
"layzspa/button":
"value_sensor.button":
if_expr: '! isnull( payload )'
expr: "payload"
and in reactor.yaml I have:
"layzspa_states":
name: "Lay-Z-Spa States"
friendly_name: 'Lay-Z-Spa States'
include: layzspa_message
I realize my MQTT configuration might be a bit unorthodox, but could there still be something unintentional in the latest MQTTController build? If needed, I can provide detailed logs.
Since today is my birthday - and I still pretend to be unconventional - I'm giving away a present to this wonderful community and I'm releasing my first OpenSprinkler controller for MSR. It was real fun to code it - and while it's still WIP, it seems to work OK for me. It's polling-based at the moment, but I'll add support for updates via MQTT very soon (it's already partially coded).
Get it at (install is similar to MQTTController and such):
https://github.com/dbochicchio/reactor-opensprinkler
Feel free to try it. It's beta software, but it's stable. I'll update it weekly until all the tasks from my todo list are empty.
Since I've learnt a lot from this controller, I'll explore new controllers soon.
Good day all,
I'm in the process of trying to shut down my 10 year old Linux home server that served many purposes, but primarily it's what I used for my NAS/Plex Media server. I migrated the NAS aspect of the server in November of last year to a true NAS solution (Ubiquti UNAS Pro), which is rack mount and much more efficient than my old tower, which it's only side benefit was heating my home office during the winter. Unfortunately it also means heating my home office during the summer, which were about to be in full swing.
I have two things running on this 10 year old server at this point. MSR and pi-hole. I'm running Plex Media Server on Fedora Workstation in Podman on mini PC, which is much more energy efficient than my old tower. My next step is to migrate MSR. I know there are images of MSR out there, and creating it is well documented. I'm going to be using Podman instead of Docker for various reasons, but they work very similar. What I don't know, is what I need to do to migrate my existing Bare Metal installation over to a container.
Has anyone done this? Any advice?
Build 21228 has been released. Docker images available from DockerHub as usual, and bare-metal packages here.
Home Assistant up to version 2021.8.6 supported; the online version of the manual will now state the current supported versions;
Fix an error in OWMWeatherController that could cause it to stop updating;
Unify the approach to entity filtering on all hub interface classes (controllers); this works for device entities only; it may be extended to other entities later;
Improve error detail in messages for EzloController during auth phase;
Add isRuleSet() and isRuleEnabled() functions to expressions extensions;
Implement set action for lock and passage capabilities (makes them more easily scriptable in some cases);
Fix a place in the UI where 24-hour time was not being displayed.
Hi guys,
Just wondering how you guys organize your rule sets and rules. I wish I had an extra layer to have some more granularity, but my feature request was not popular.
Maybe there are better ways to organize my rule sets.
I use the rule sets now primarily for rooms. So a rule set per room. But maybe grouping by functionality works better. Any examples/ suggestions would be appreciated.
I have the following yaml configuration in local_mqtt_devices file
x_mqtt_device:
set_speed:
arguments:
speed:
type: str
topic: "command/%friendly_name%"
payload:
type: json
expr: '{ "fan": parameters.speed }'
While this works fine, I'm wondering how this could be changed to "fixed" parameters, as in this case "fan" only accepts "A", "Q" or a numeric value of 1-5?
HASS 2022.5 issue with ZwaveJS in MSR
-
Running zwavejs-22118-baab576 in MSR, HASSOS 2022.5.1
Due to an unreported issue in HASS, when I upgraded the 2022.5 yesterday, it dropped ZwaveJS2MQTT from my HASSOS build. Finally got it reinstalled and it appears to be working the way it was previously.
MSR is now showing zwavejs down and in entities, nothing is updating.Seeing this in the logs:
ZWaveJSController#zwavejs ws_open caught [Error]Error: connect ECONNREFUSED 192.168.0.16:3000Are there additional steps needed that are not mentioned in the manual?
At a loss to figure out what is causing issue. -
Well, I was hoping one of the HassOS users would chime in here. I don't use it. But, if memory serves, installing zwavejs-server or zwavejs2mqtt from inside HassOS installs it in a way where nothing outside of the HassOS container can access it. You have to install it outside of HassOS as a parallel package. Beyond that, no idea, but that would be my first guess. Other than that, you need to make sure the WS Server is enabled in zwavejs2mqtt (in its settings under Home Assistant), but if that wasn't already enabled, I'm guessing Hass wouldn't be able to access it either (and you didn't say if it could or could not).
Also please review the posting guidelines' advice around posting log snippets (no context included in your post and not formatted correctly).
-
Patrick,
As far as I know everything is set up the same as it was before I upgraded to HA 2022.5. I did reinstall Zwave2mqtt because of a version issue. But it is set up as it was prior. WS is enabled and listening on port 3000 which matches the reactor.yaml config.These lines in the log are the only thing I see related to this issue. Everything before and after is rules evaluations.
[zwavejs-22126]2022-05-08T17:10:29.926Z <ZWaveJSController:6:Controller.js:529> [ZWaveJSController:tick()] entry [zwavejs-22126]2022-05-08T17:10:29.926Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs connecting to ws://192.168.0.16:3000 [zwavejs-22126]2022-05-08T17:10:29.927Z <ZWaveJSController:6:Controller.js:538> ZWaveJSController#zwavejs:run() took 1ms [zwavejs-22126]2022-05-08T17:10:29.929Z <ZWaveJSController:WARN> ZWaveJSController#zwavejs websocket error during open/negotation: [Error]Error: connect ECONNREFUSED 192.168.0.16:3000 [zwavejs-22126]2022-05-08T17:10:29.929Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs websocket to ws://192.168.0.16:3000 closed during open/negotiation [zwavejs-22126]2022-05-08T17:10:29.930Z <ZWaveJSController:5:Controller.js:767> ZWaveJSController#zwavejs ws_open caught [Error]Error: connect ECONNREFUSED 192.168.0.16:3000 [zwavejs-22126]2022-05-08T17:10:29.930Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs connection to ws://192.168.0.16:3000 failed; will retry [zwavejs-22126]2022-05-08T17:10:29.930Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs retry 727 delay 120000This repeats itself periodically but not seeing any additional zwavejscontroller messages.
For the zwavejs test, where there any additional configuration requirements that are not included in the manual?
Any additional logging I can enable, or additional info I can provide?Next step is to roll back HASS version to 2022.4 that was working.
-
I use 2022.5.1 with zwavejs2mqtt and Reactor, all works. Something in your setup isn't happy. I assume you have right IP address for the Hass/zwavejs2mqtt system?
Since it's a not-connect issue, there's no additional debug that would be of any value. That's the problem you're solving.
-
T toggledbits locked this topic on
