Rule condition shows TRUE in UI but Rule never transitions to SET — survives full restart

[cw-kid]

Clearly the problem is I don't know how to structure or write the required yaml code. Following @therealdb example above, I changed mine to this:

- id: mqtt
  name: Mosquitto
  enabled: true
  implementation: MQTTController
  config:
    entities:
      tasmota_fan_controller_temp:
        name: "Stairs Cupboard Temp"
        include: tasmota_sensor_temperature_humidity
        topic: "fan_controller"
        source: AM2301   

I could then finally see an Entity for it in MSR for the Temp sensor. But with no data values as yet its null.

That obviously only imported the DHT22 (AM230) Temp sensor part.

I then tried to add this to also include the 1 channel Relay part.

- id: mqtt
  name: Mosquitto
  enabled: true
  implementation: MQTTController
  config:
    entities:
      tasmota_fan_controller_temp:
        name: "Stairs Cupboard Temp"
        include: tasmota_sensor_temperature_humidity
        topic: "fan_controller"
        source: AM2301
      tasmota_fan_controller_relay:
        name: "Stairs Cupboard Fan"
        include: tasmota_generic_relay
        topic: "fan_controller"
        source:
        unit: "1"  

The relay part seems to be working! I pressed the "Perform" button and was able to turn on and off the relay / fan OK.

Seems I didn't need a "Source:" for the relay portion, I left that blank as I didn't know what to put in there anyway.

So just not sure why I have no data from the Temp sensor currently.

[therealdb]

@cw-kid post some screenshots from mqtt explorer. It’s easier to follow, if you want my advice.

[cw-kid]

Its working now, a wire came off the ESP board for the DHT22 which is why it was null. I connected the wire again and now I see data in MSR.

So this seems to be the now working yaml code:

- id: mqtt
  name: Mosquitto
  enabled: true
  implementation: MQTTController
  config:
    entities:
      tasmota_fan_controller_temp:
        name: "Stairs Cupboard Temp"
        include: tasmota_sensor_temperature_humidity
        topic: "fan_controller"
        source: AM2301
      tasmota_fan_controller_relay:
        name: "Stairs Cupboard Fan"
        include: tasmota_generic_relay
        topic: "fan_controller"
        unit: "1" 

And I did just install MQTT Explorer so a screen shot of that:

Thanks for everyone help, I just needed a nudge in the right direction with the MSR yaml code.

[cw-kid]

What else can I build! I have loads of spare ESP boards and sensors laying around the place, what I was using when trying out "EzloPi" but I am gonna switch to Tasmota / MSR and eventually Home Assistant when I retire my Vera Plus for Z-Wave duties.

[cw-kid]

Sweet everything appears to be working now, I created some virtual devices in Vera for the Temp and Humidity and some new MSR rules to push those values to them in Vera if they change.

Updated my Home Remote dashboard and I can see them on my phone now and also have a switch to turn the Fan on and off..

!

!

[therealdb]

@cw-kid I have them with lux, barometric, distance, and temp/humidity sensors, while also using a couple as Bluetooth bridges. in this regard, your fantasy is the real limit.

I've recently moved everything I could to ZWave, because it is better in terms of stability, but ATM there's no equivalent for fancy sensors, even if ZigBee has a denter offer.

[cw-kid]

Actually I do have one issue: power_switch.state=null

It seems MSR is not seeing what the state of the relay currently is? Which is causing me an issue now in a rule I am trying to create.

If I run this command in terminal on the MSR / MQTT broker box

:~mosquitto_sub -v -t 'tele/fan_controller/#' -t 'stat/fan_controller/#'

I see this:

tele/fan_controller/LWT Online
tele/fan_controller/STATE {"Time":"2026-02-16T18:38:48","Uptime":"0T03:13:09","UptimeSec":11589,"Heap":113,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"Berry":{"HeapUsed":4,"Objects":50},"POWER":"OFF","Wifi":{"AP":1,"SSId":"ASUS_86_2G","BSSId":"04:D9:F5:74:C5:E0","Channel":3,"Mode":"HT40","RSSI":100,"Signal":-20,"LinkCount":1,"Downtime":"0T00:00:04"},"Hostname":"Stairs-Cupboard-Fan-ESP32","IPAddress":"192.168.0.49"}
tele/fan_controller/SENSOR {"Time":"2026-02-16T18:38:48","AM2301":{"Temperature":21.2,"Humidity":47.9,"DewPoint":9.7},"TempUnit":"C"}
stat/fan_controller/POWER OFF

stat/fan_controller/POWER OFF

Which is correct, the fan is currently off.

So maybe the yaml code is not quite right if its not seeing the state of the relay.

I can turn on / off the relay however via MSR so it is talking to it somewhat.

This is what is in the reactor.yaml file currently.

- id: mqtt
  name: Mosquitto
  enabled: true
  implementation: MQTTController
  config:
    entities:
      tasmota_fan_controller_temp:
        name: "Stairs Cupboard Temp"
        include: tasmota_sensor_temperature_humidity
        topic: "fan_controller"
        source: AM2301
      tasmota_fan_controller_relay:
        name: "Stairs Cupboard Fan"
        include: tasmota_generic_relay
        topic: "fan_controller"
        unit: "1"  

[cw-kid]

Looking at the HTTP output for everything from the Tasmota, I see these snippets.

"StatusSTS" - seems to contain the state of the relay e.g. "POWER":"ON"

"StatusSTS":{"Time":"2026-02-16T18:58:25","Uptime":"0T03:32:46","UptimeSec":12766,"Heap":106,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"Berry":{"HeapUsed":4,"Objects":50},"POWER":"ON","Wifi":{"AP":1,"SSId":"ASUS_86_2G","BSSId":"04:D9:F5:74:C5:E0","Channel":3,"Mode":"HT40","RSSI":100,"Signal":-19,"LinkCount":1,"Downtime":"0T00:00:04"},"Hostname":"Stairs-Cupboard-Fan-ESP32","IPAddress":"192.168.0.49"}}

Where as "StatusSNS" contains the Temp data.

"StatusSNS":{"Time":"2026-02-16T18:58:25","AM2301":{"Temperature":19.8,"Humidity":50.3,"DewPoint":9.1},"TempUnit":"C"},

So it seems MSR doesn't know where to find the relay status / state currently? and I am not sure how to fix it.

As a guess I tried adding source "POWER" to the relay section of the yaml but didn't seem to work and bring in the "ON" or "OFF" value.

tasmota_fan_controller_relay:
        name: "Stairs Cupboard Fan"
        include: tasmota_generic_relay
        topic: "fan_controller"
        source: "POWER"
        unit: "1"

I was poking around the file system to find these Tasmota default templates. I see this folder but its empty.

/home/stuart/reactor/config/mqtt_templates

I do see a file called tasmota.yaml however in this folder.

/home/stuart/reactor/ext/MQTTController/templates

EDIT: I just fixed it by changing unit: "1" to unit: "" in the reactor.yaml.
It now say "false" for power state in the Entites area. I thought I had to put a 1 in unit because in Tasmota somewhere, I saw the Relay was number 1.

[toggledbits]

Tasmota has this inconsistency where if there's only one relay configured, it does not include the relay number; if more than one, then it adds it. There's no way for the template to know how many relays are configured, so you found the correct fix.

[cw-kid]

@toggledbits I plan to add a second relay or replace it with a dual relay board, so will see how that works out with these Unit numbers.