Hi folks,
I currently have some cheap Zigbee hub and some Amazon Alexas running my smart home which mostly consists of Zigbee power strips and Zigbee battery powered switches.
It all worked OK originally, but now whenever I press a Zigbee switch the light in the corresponding plug switches on then immediately off again.
If I ask Alexa to turn the light on it works fine. Likewise if I switch it on from my phone.
Any ideas what the issue could be?
I've tried unplugging the hub a number of times but that doesn't seem to fix it.
I was thinking about getting a Homey Pro 2023 to speed things up (tmas the Zigbee hub seems to be really slow now as well, for some reason) but I'm not sure about that either.
Any suggestions greatly appreciated!
Hey guys...
We are replacing the heat pump and furnace this week and I will also need to replace my nest thermostat at the same time 'cause Nest is ending the cloud thing end of the month.
Anyway, I'm looking to use the
That's what the heat pump installer recommend BUT, using Nest I was also using it to control the home humidifier using a single wire connected to nest... but no low voltage thermostat is able to do that, I checked all of them...
So I need some help on how I can do that, to connect the home humidifier using zwave also....
Hi
We are looking for a solution where we can detect presence of a «thing» (people , car , dog, cat, and more..
We need:
fast detections, 1-3 seconds in range from 0 to 20 m from «base» fysical «client» , chip , transmitter , unit. base , receiver placed at a door, gate, house, etc uniq Identifying wirelessThe client:
no need for pressing any thing (no buttons) battery , hoply 2-5 years battery time.Have someone done anything like this?
What technologi will be best?
Hey everyone, I'm currently working on developing a bed sensor that can detect when you're out of bed. It could be used to trigger other smart home gadgets, like lights or blinds, temperature etc.
The sensors are placed under the legs of your bed post. Should look and feel like "smart furniture pads" with size 2 inches in diameter and 1/4 inch thick.
Before we go any further, I'd love to get your thoughts on this - would a bed sensor like this be something you'd find useful? We're still in the early stages of development, so any feedback you have would be greatly appreciated. Thanks in advance!
@DesT, fenced code blocks display differently after the upgrade.
abc defThe above should display as abc and def on two separate lines. This works. But this fails:
verbose: true config: data: "auto"The above should display as three lines, verbose: true, config: and data: "auto", but this fails. In order to make it display properly, I now have to open the fenced code block with ```text (specify language, generic text). This displays without highlighting. The words yml and yaml (and the all-caps versions) don't seem to be recognized. I can also use js to get JavaScript highlighting, but this isn't great for YAML. Here's the same block with the language (text) specifier added (no other changes):
verbose: true config: data: "auto"Sure, we can start adding language specifiers to our new posts, but I suspect if we start digging around old posts, we're going to find a lot of broken display of the fenced code blocks (plain ``` at the start with no language specifier) in the thousands of old posts in these forums, upon which people still rely for answers and information.
Log file snippets also get similarly brutalized:
[###BUILDVERSION###]2023-04-26T19:41:51.683Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs added file logger to zwavejs.log [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_device_cfg, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_mfg_spec, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_device_ver, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.747Z <ZWaveJSController:WARN> zwavejs_capabilities defines x_zwave_values, which is not consistent with the recommended naming [###BUILDVERSION###]2023-04-26T19:41:51.837Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs connecting to ws://192.168.0.10:3000 [###BUILDVERSION###]2023-04-26T19:41:51.874Z <ZWaveJSController:NOTICE> ZWaveJSController#zwavejs connected [###BUILDVERSION###]2023-04-26T19:41:51.874Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs sending connection initialization [###BUILDVERSION###]2023-04-26T19:41:51.931Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs greeting from server: [Object]{ "type": "version", "driverVersion": "10.16.0", "serverVersion": "1.28.0", "homeId": 3631280043, "minSchemaVersion": 0, "maxSchemaVersion": 28 } [###BUILDVERSION###]2023-04-26T19:41:51.932Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs performing initial inventory [###BUILDVERSION###]2023-04-26T19:41:52.325Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs manufacturer-specific data for 134 (AEON Labs) from package ver 22315.1 [###BUILDVERSION###]2023-04-26T19:41:52.328Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs configuring node 1 endpoint 0 (entity "1-0") [###BUILDVERSION###]2023-04-26T19:41:52.339Z <ZWaveJSController:INFO> ZWaveJSController#zwavejs manufacturer-specific data for 543 (Elexa Consumer Products Inc.)I think this is going to be a problem. Is there a way in NodeBB to configure the default language for fenced code block markdown for the entire forum so that these display more as they did before the upgrade?
EDIT: Examples below of old posts with corrupt formatting now:
https://smarthome.community/topic/1101/dynamic-groups-controller-filter-expressions
https://smarthome.community/post/11362
This last old post is interesting, because the first block displays incorrectly, but the second block is OK. In playing around, there seem to be triggering character sequences, suggesting that the markdown processor is trying to "guess" the language but not getting it right, perhaps:
Hi guys,
we are doing a survey in IT privacy and security and we want to analyze the user perception of privacy concerns in smart homes. It will only take 5-10 min to fill out the survey 🙂
i would be very thankful if you could take part and help us to get as many responses as possible.
Thank you!
Can anyone help with the MIOS UI5 weblink? Not the getvera one.
Still running UI5 on a couple of sensors & lights and need to tweak PLEG but for the life of me I can't remember the link to tunnel back to the trusty machine....
The wifi on my router is turned off, and wifi around the house is provided using a mesh - 3 units altogether (one connected directly to the router) that are spread around the house.
I would like to start automating certain tasks around the house and intend to try adding a few smart sockets to my setup.
The mesh system I have supports both 2.4GHz and 5GHz, and does not provide me with the option to control them - i.e. turn one or both on/off, give each a different SSID, etc.
The devices I wish to purchase/use only support 2.4GHz.
Will turning the mesh units off and temporarily turning the 2.4GHz wifi on the router to allow me to set them up be enough? Will I then be able to return to my usual setup and everything will work as it should?
Many thanks in advance
ChatGPT samples:
Me:
Tell me about an iot program called openLuup.
It:
OpenLuup is an open source home automation system that is built on the VeraLuup platform. It is designed to be easy to install and configure, and provides users with a powerful and versatile way to control their home automation devices. OpenLuup offers a wide range of features, including support for many popular home automation devices, scheduling, scripting, and integration with other services. OpenLuup is designed to be customizable, allowing users to create their own home automation systems. It is an excellent choice for those looking to create their own home automation system without spending a lot of money.
Me:
Write an iot program using openLuup.
It:
--openLuup IoT Program-- -- Initialize Variables -- local device_id = "MyHomeDevice" local temperature_sensor_id = "MyTemperatureSensor" local temperature_threshold = 75 -- Create Devices -- luup.create_device("OpenLuup Temperature Sensor", 0, device_id, "D_GenericSensor1.xml", "I_GenericSensor1.xml", "S_TemperatureSensor1.xml", "") luup.variable_set("urn:upnp-org:serviceId:TemperatureSensor1", "CurrentTemperature", 0, device_id) -- Start Timer -- luup.call_delay("check_temperature", 10, "", false) --Function to Check Temperature-- function check_temperature() local current_temperature = luup.variable_get(temperature_sensor_id, "CurrentTemperature", 0) --Check Temperature Threshold-- if current_temperature >= temperature_threshold then --Send Alert-- luup.call_action("urn:micasaverde-com:serviceId:HomeAutomationGateway1", "SendTextMessage", {PhoneNumber="1234567890", Message="ALERT! Temperature exceeded threshold!"}, 0) end --Reset Timer-- luup.call_delay("check_temperature", 10, "", false) endMe:
Write an iot program using openLuup.
It:
Write an iot program using openLuup. -- openLuup IOT Program -- -- Variables local lampState = false local lampTime = 0 -- Functions function lampTimer() if lampTime > 0 then lampTime = lampTime - 1 if lampTime == 0 then luup.variable_set('urn:upnp-org:serviceId:SwitchPower1', 'Status', 0, lampDeviceID) lampState = false end end end -- Setup luup.call_delay('lampTimer', 60, 0) -- Main Loop while true do -- Check for motion if luup.variable_get('urn:micasaverde-com:serviceId:MotionSensor1', 'Tripped', motionSensorDeviceID) == '1' then if not lampState then luup.variable_set('urn:upnp-org:serviceId:SwitchPower1', 'Status', 1, lampDeviceID) lampState = true -- Set lamp timer to 5 minutes lampTime = 300 end end luup.sleep(1) endWhat??
luup.sleep(1)Not good - looks like I still have some semblance of a job to fulfill.
Me:
An iot program called openLuup was written by akbooer. Who is akbooer?
It: (note: answer redacted and as I understand it, also incorrect re: AltUI):
akbooer is the pseudonym of the software developer and home automation enthusiast. He is the creator of the openLuup home automation software, which is an open-source version of the Vera home automation system. He is also the creator of the AltUI graphical user interface for openLuup.
Me:
Who created of the AltUI graphical user interface for openLuup.
and
Me:
Who created of the AltUI graphical user interface for the home automation system Vera.
Names two different people - mmmm.
Regardless very impressive - give it a few more years.
...which I'd like to do. I know I go about these things all wrong (namely think of something I'd like to do, then try and work out what I need to know) but that's me 🙂
Just looking for some pointers on what I should google for really:
What I'd like is to provide a selection of (basically two word) phases which I can select from randomly (or even pseudo randomly) and pass to Alexa to be spoken. There are 10 such phrases only.
So what should I be reading up on to get me started?
TIA for any guidance
C
Hi,
I am a student and recently i am working on smart home project and writing a seminar paper about the way users handle and manage IoT devices. I you have 3 min, please fill below survey. Its really short.
Thank you in advance, I really appreciate everyone's help.
For what it's worth, I've been putting the finishing touches on a much-updated version of my DP Apps spreadsheet -- specifically intended for HE users, at least for now -- and invite you all to take a gander http://bit.ly/hedb23 at the PDF one-page version.
Corrections and edits welcome (esp. for the HOMEKIT column, just added yesterday)! Thanks in advance, especially because I'm not a big dashboard user myself, but somehow accepted this role as "keeper of the list" as it were.
Hello guys,
I would like to achieve two different things with lights, but I am not sure it could be done. I am starting with smart things, and I am far from any electrician knowledge, wo any help is really appreciated.
I have dumb switches in my hall, controlled from 3 places. I understood that installing one smart module before first switch will make them "hybrid", both smart controlled and dumb controlled.
I would like to buy ceiling light with two bulb sockets. What I would like to achieve is I would like to have one bulb for normal daily usage (lets say cold white full brightness), and second for night time (aprox from 10pm till morning) with some red/orange - minimum brightness.
So question are:
Is there a way to keep both bulbs turning-on separated? So only one will be on during day, and then only second during night?
And could that be done with pressing dumb switch? What would I need to achieve it? (maybe another module into the ceiling lights)
Thank you in advance
MIOS down
-
Oh no it's still there. Claiming everything is hunky dory.
Just got an email saying it was due to maintenance:
Early this morning we pushed an update to our cloud server, but unfortunately, this update took longer than expected to deploy and has resulted in you being unable to access your systems or control your homes.
Which no one knew about (it seems apart from @therealdb ) including the guy that runs support.
C
-
Dear Vera Customers,
Early this morning we pushed an update to our cloud server, but unfortunately, this update took longer than expected to deploy and has resulted in you being unable to access your systems or control your homes.
We understand the responsibility that comes with putting our systems in your homes and apologize for the inconvenience this has caused many of you. The system should be up and running shortly, though due to the number of users trying to reconnect, access may be delayed a bit further.
Please note: during the update, the system was returning an incorrect username or password error, but you do not need to update either of these. Once the system is back online your usual username and password will work as normal.
Again, we apologize for the inconvenience and appreciate you being a loyal Vera customer.
Regards,
Mark Samuel
CEO, Ezlo Innovation -
Cloudless FTW! People need to go back to what was the real purpose and benefit from the cloud and stop moving applications there because they can. I see this in the corporate world as well... The cloud's benefit is sharing and offloading things you can't do at home due to lack of processing power. This in no way applies to home automation which needs and certainly wants no sharing and even less requires the processing power to justify the power needed, the reliability/performance loss and the security liability to send your data into the wild.
On related note, their cloud is of the same quality as their products!! I just got an ezlo Atom 2 beta in the mail a couple of days ago in spite of having sent them an email not to send this to me as it would just add to my pile of garbage. Well it is here and completely scratched up looking like it got pulled from the ocean. It went straight to the trash can. The atom concept itself is self defeating and I fail to understand any sort of application for it besides adding RF interference and latency to any home setup. It is a product designed from gross ignorance about RF, zwave and home automation...
-
I see this in the corporate world as well... The cloud's benefit is sharing and offloading things you can't do
No argument from me.
Terrible operational awareness as well. Private conversations blame C19 because the teams are working from home.
I guess it sounds like I'm kicking them for the hell of it, but blimey, it's what, 2 years since the take over? This is basic basic stuff.
What I see being reported as issues with Ezlo testing seems they have a very very long way to go before that's ready for prime time as well.
When will we get voice control for OpenLuup?
C
-
-
https://smarthome.community/topic/41/voice-control-and-tts-projects
All running on the same machine as z-way and openLuup. (a VM running on a single thread of my quad core 8 thread NAS)
Note that these provide much better control over what gets discovered and how they behave vs the cloud hosted solution. I can do a lot of things the cloud solution could not... in terms of action and device controlled. -
Yes it would work on a rPi3 even or in my case I ran it for a long time on a celeron. It does't really exercise anything on the CPU:
z-way server occupies ~5%, openLuup (which is massive... over 300 devices and 200 scenes now) only takes 3% ALTUI spikes another 3% at the most with my latest discovery of rapidjson, and these bridges all take less than 0.5% together. RAM required: 500MB. Honestly I could almost run it on the vera plus if I could compile all these for ramips. This supports my point about not needing a very powerful CPU for processing but we need to pay attention to the I/O bandwidth and network capacity/cpu storage reliability. Complete opposite of the ezlo plus which upgrades what doesn't matter and downgrades what is important vs the vera.
If you do want to expand later into the video realm though at this point I would recommend the nVidia Jetson Nano...
which is equivalent to rPi4 with a GPU.