I have a kitchen light that can be controlled by two switches, using either to turn it off or on. I have been slowly changing things over to be a smart home but this is the first switch I am attempting to install.
I am in a double wide modular home (mobile) that was built in 1994.
At first I thought I would need a 3 way switch but when taking the normal switches apart I realized that was incorrect because the wiring on my switches are different than anything I could find online.
For one a 3 way smart switch requires 5 wires and there are only 2 wires going into the primary switch with 3 wires going into the secondary switch from the primary switch (at least I think the 3 wires connect the two switches together). Images will be attached of the wiring.
There are two wires (one black and one white) going into the first switch and 3 wires (black, white, and red) going out of that and into the second switch (I assume). The odd thing is the red wire going to the second switch is connected to the white wire going into the first switch and the white wire going into the second switch seems to be a bridge wire or a traveler wire. Not exactly sure. You will see what I mean in the images.
I need to know what kind of smart switch I can use in this set up with one remaining a normal switch.
Note that for some reason the images got switched around when uploading them. The image with 2 wires on one side and 3 on the other is what I think is the primary and the image with just 3 wires is the secondary.
You lot are more likely to have a view than most I know. Our much used Logitech Harmony is (not so) slowly dying.
And Logitech have discontinued the entire line.
And no one else appears to be making something similar.
Was going for a Sofabaton X1, but no numeric keypad. Sofabaton U1, but no favourites.
Anyone got suggestions?
Needs to have those features, oh and not be only a phone app.....
Since one member asked at one point about the "front end" and "back end", I drew this showing the controller from the base to the tip along with what I have found to be the best options from my testing. Almost every controller will try to integrate all elements, especially commercial ones but... they all have strengths and weaknesses so if one can have a medley of the best ones...
So, I think I'm in a bit of an unusual situation. I work at a camp & retreat center that has wifi throughout. I want to put a few switches in the office that can control outdoor lighting throughout the camp. We currently have switches in each of the buildings, but it is a particularly frustrating job to get all the lights on in the evening when it is brutally cold out or we are short staffed.
Most of our staff is not very tech savvy (my boss literally has his wife print out his emails for him each day!!!) so, I'd love to avoid having to set up any sort of raspberry pi or new phone app.
Is there type of 3-way switch that can connect to the wifi, turn on a light in another building AND turn on an indicator light in the office, without having any sort of wire running between the buildings? Hopefully looking for a simple solution without breaking the bank too.
I greatly appreciate any input that you can give. Thank you!
I have a X10 wall switch system and I want to get rid of it. What would be the easiest transition to something more modern and easy to use with either wifi/homekit capabilities? My current X10 controls 3 zones in my bedroom. All zones are dimmable.
Zone 1 is 4 canister ceiling lights. LED bulbs
Zone 2 is 1 canister ceiling lights. Halogen Bulb
Zone 3 is 1 canister ceiling lights. Halogen Bulb
I have an old plug-in remote from Radio Shack and a wall switch with 3 buttons, each controlling one zone. (images attached)
My wall switch has one two wires from the wall. One black, one white.
Is there any solution easy to install without the need of an electrician? Thanks for any feedback.
Good morning all,
I'm working on weaning myself off of being totally Vera dependent. I've installed MSR on my Fedora home server, and I've been migrating luup Reactor rules over little by little. My hope is to use Vera as a bare bones z-wave hub, until I replace it either with Ezlo (not so sure about), or perhaps Hubitat. I'm just tired of zero new development in Vera, empty promises of native device integration, and cloud services that go down and leave my automation hanging.
In any case, I digress. I've attempted to use Gcal3 on Vera to integrate Public calendars, such as Federal Holidays, School Calendars, etc. It use to somewhat work, but more often than not, all I get from Gcal3 is "token error code: HTTP/1.1 400 Bad Request". The developer no longer is active, and it's effectively not working anymore.
I'd like to use these public calendars as Entity Attributes or Constraints in MSR. For instance, if it's a Federal Holiday, I don't have to work, and I may want to sleep in, which means lights may not come on as early, window coverings in the bedrooms may open later in the day, etc. Similar idea with a school calendar. If "closed" is in the event, my daughter may want to sleep in, and not want the window coverings opened as early.
I'm aware that Ezlo has integration through NuCal to all sorts of web based services, including Google Calendar, but as I stated earlier, I'm undecided on going down that path. Is there anyway to do this on MSR through any of it's abilities, such as HTTP calls or MQTT ( not experienced in MQTT, so I don't know now it works really).
Has anybody already done this?
Thanks for any advice in advance.
How do you post images on this forum from a smart device?
Is there a guide somewhere on how to submit images/attachments from a smart device ?
As someone who accesses this forum from an iPad/iPhone, I don’t have the ability to drag / drop images into any posts.
What are other people doing (who are not using a traditional PC/MAC) ?
akbooer last edited by
If you use the blue REPLY button at the top of a post, rather than the link at the bottom, you get an form with a number of icon buttons, one of which is an image which enables you to upload.
All the drop down from the top right blue Reply button gives me is “REPLY AS TOPIC" I don’t get anything else ?
rafale77 last edited by
Don't use the drop down... just click on the reply button.
When I hit REPLY to an existing thread, the options are there at the top of the new “replying to’ window.
But when I click to do a NEW TOPIC, the options are not there.
LibraSun last edited by
That's right. When you begin a new topic you don't get any formatting tools for some reason. That's why I always start with a basic introduction paragraph and then do the meat and potatoes in the subsequent replies.