After the veralert service was shut down and Richard confirmed that it will not be available again, I searched for a new notification service to use in my vere secure. I signed up for the PushOver service.
I want to take a snapshot from a camera with camera snapshot address “192.168.4.37/img/snapshot.cgi?size=4&quality=1” and video address “192.168.4.37/img/video.mjpeg” according to a trigger.
Actually, someone (Tlex) did a work about this years ago on the vera forum, but I couldn't understand that script. I also wrote to him to be more descriptive, but I didn't get an answer. Can you help me with this?
Let's assume you have done the following:
Downloaded and installed Z-Way following these instructions. No Zway license is required to do the following.
The software is now all up and running with your UZB stick (whole other post).
Dial up this Zway web page: http://<Zway_server_IP_address>:8083/expert/#/network/controller
Under the heading "Firmware" take note of the "SDK version" and the "Serial API Version". Say they equal 6.71.01 & 05.23 respectively like it shows here.
Now on to Vera:
Go to the Vera UI --> Z-Wave Settings and taken note of the "Version" shown for Vera's internal Zwave IC. For example purposes, say it equals "6.01".
You plug your UZB stick into Vera.
In the Z-Wave Settings you set the port to "/dev/ttyACM0"
You've rebooted Vera, so that it starts using the UZB stick.
OK, so what "Version" will Vera now display and the version of what? The version shown by Vera is the "Z-Wave protocol" version or the "Serial API" version - it's unclear which but I suspect the former. However on most occasions the numbers are the same. It's not the Software Developers Kit (SDK) version number.
Knowing the UZB firmware version you can identify what Vera will show with the following table.
From the example above: Zway stated the version as 5.23. It will show in Vera as version 4.61 - see table. However the Vera internals showed up as 6.01. So using this method to copy the Zwave configuration to the stick will not work, as the stick represents a downgrade and you can only do same to same or upgrades. So in this case you need to update the stick firmware from 5.23 to 5.32 as a minimum. Then the stick will show up in Vera with version of 6.01.
Which is great. So you then use the Zway software to upgrade the stick firmware. And that's the last you hear from it because this happens:
"Sorry to inform you, but there is a known issue in some UZB manufactured by our partners on license base that after upgrade they become bricked."
And you have to do this to unbrick it. So time to try someone else's stick. Sigh.
ZWay UZB version
Vera version
SDK version
5.39
6.09
6.82.01
6.08
6.82.00
6.07
6.81.06
6.06
6.81.05
6.05
6.81.04
6.04
6.81.03
6.03
6.81.02
5.37
6.02
6.81.01
5.36
6.02???
6.81.00 ????
5.33
6.02???
6.81.00 ????
5.32
6.01
6.81.00
5.03
6.71.03
5.02
6.71.02
5.27 BL 48059
4.61
6.71.0?
5.26
4.61
6.71.0?
5.23
4.61
6.71.01
4.6
6.71.00
5.2
4.6?
6.7?.00
5.16
4.6?
6.70.00
4.62
6.61.01
4.33
6.61.00
4.54
6.51.10
5.07
4.38
6.51.09
4.34
6.51.08
4.24
6.51.07
4.05
6.51.06
5.06
4.01
6.51.04
3.99
6.51.03
3.95
6.51.02
3.92
6.51.01
3.83
6.51.00
3.79
6.50.01
3.71
6.50.00
3.67
3.35
6.10.00
3.41
6.02.00
3.37
6.01.03
2.78
The table is based on page 434 of silabs app INS13954 and the UZB firmware revision information found here. The table may have errors!
The vera can run both its zwave and zigbee network off of external USB radios instead of the onboard ones. This could have advantages in terms of portability, facilitating migrations or recoveries in case the vera craps out. It could also enable testing of newer radio firmwares.
Zwave is pretty straightforward as its serial API is standardized and the protocol is the same regardless of what brand of USB stick you use. I have run my vera off of USB sticks of various brands for years going from Aeotec, Zooz, Homeseer and even the most generic silabs/Sigma Design. You just insert the stick in the usb port, find out which serial port it created (under the /dev/ folder) and use that port (ie. /dev/ttyACM0, /dev/ttyUSB0 etc) in the zwave advance menu.
Zigbee is a little trickier as the protocol and chipset was not quite as standardized as zwave. The vera only works with ember Znet protocol and you will need to find a usb stick with an EM35x chip in it which already has an ember zigbee firmware loaded. One example of such a stick is the Go Control HUSBZB1 (dual zwave-zigbee stick). The port is not readily accessible on the vera UI but can be accessed either through editing of the /etc/cmh/user-data.json or through ALTUI by going into the hidden zigbee radio device through the "table devices " menu and changing modifying the port variable there.
You can also upgrade the onboard zwave and zigbee radio firmwares from the command line SSH...
Good morning all,
I've got a stable Home Assistant running on a RPI 4 with a Aeotec Z-Stick 7 Plus, and of course the Z-wave JS integration. I've manually moved a handful of devices, and I'm overall much happier with the HA z-wave capability than I am with Vera. There are still some things I'm trying to figure out that I have in Vera that I'm not sure how they'll work in HA, but no deal breakers.
I've got all of my automation on MSR and off of luup Reactor, so really the only thing left for me is to migrate my Z-wave network. I saw @rafale77's post about using a Zwave.me UZB1 to Zway, but of course that's not what I'm using.
Is there a similar method that I can use my Aeotec Z-Stick 7 plus to Home Assistant? I have around 70 Z-wave devices (give or take devices that generate multiple instances in Vera), so manual unpairing, including, etc, would be quite a chore.
So ... I am trying to do the following:
Current setup:
Vera Plus (1.7.4955) Zwave only -> HASSIO VM (full control via Vera Integration)
Future Target:
HASSIO VM (leveraging zwave.me UZB1 dongle via USB)
I have done the following so far:
Updated UZB1 dongle (via RPi SmartHome) to latest 5.39 Firmware
I followed the following steps to try and migrate my existing Z-Wave NW (currently on Vera) onto the UZB1 dongle following the steps listed here:
Migrate from Vera to Z-way
Problem:
Steps 1-3: went fine (although the dumps are labeled as dongle.6.1.dump.x)
Step 4: went fine and the UZB1 was recognized as it should be (per dmesg)
Step 5: updating the port to /dev/ttyACM0 went fine, although I didn't see any indication of luup reload (or a save button for that matter when updating the port mapping)
Step 6: I did the touch for dongle.restore, but wasn't sure where to trigger a luup reload (I assumed it was Z-Wave Settings > Advanced > Reload Engine). I believe I got an error message when trying to do that step
Step 7: verify dongle.restore.go I don't recall being in the directions when I was going the test, but I rebooted
Post Reboot: None of my previous z-wave devices were listed. I also checked dmesg via ssh and noticed the following items:
[ 4.328000] Unsupported Device!
[ 4.328000] Vendor=658 ProdID=200
[ 4.328000] Manufacturer= Product=
I saw that item a couple times which almost seems like Vera is blocking the UZB1 or at least complaining about it.
I ended up switching the Z-Wave back to the embedded controller, and restoring configuration from backup.
Any suggestions what I did wrong??
Having trouble getting a Vera 3 to recognise a Z-Wave.Me UZB stick.
WinSCP indicates it's mounted at /dev/ttyACM0, so the Vera Z-Wave settings were adjusted to match. On a Luup engine reload Vera UI states: "ZWave : Failed To Start". Ditto for a complete Vera reboot.
Has anyone successfully used a UZB stick with a Vera 3?
Hello Everyone,
I am using iPhone locator on Vera, and yesterday it stopped working. Looking at the logs, I can see the connection is refused, but nothing on my end changed. iPhone locator is really important in my particular setup, so I guess I have two questions.
Is it broken, or is it me?
I don't see anyone else saying there is an issue, but I am not sure how many people are still using it (or Vera for location) at this point. I installed it on a blank Vera test controller, same issue. It might be something with the iCloud account, but it works everywhere else.
Is there something similar on another platform?
Mainly what I would like is the ability to force a poll of iCloud location on demand. I have a bunch of triggers setup, including magnetic sensors in my driveway to sense vehicles and determine if the motion is egress or ingress. These triggers in conjunction with MSR have been a great way to double check phone location, and I would hate to lose this functionality. It looks like HA might have something with "iCloud3". Is anyone using it?
Thanks,
Mike
@akbooer said in
The only thing left on Vera is now electricity meter readers, and I simply can't find any suitable WiFi replacement.
My hem stopped reporting this august and I’ve replaced it with a Shelly EM. I’m using another one on my solar and they’re amazing fast to report and quite precise. They’re WiFi, and mqtt based. Recommended!
Long story short: I need to tweak some parameters for Fibaro Plugs, to remove frequent notifications about watts (I just need a very good approximation, in order to detect the cycle of washer/dryer), but the parameters depend on the firmware version, and I have:
271,1554,21554
and the other one has:
271,4102,0
Any help is apprreciated.
So, I recently added Pi-Hole (pi-hole.net) to my networked clients for its open-sourced Ad and Tracker Blocking. Essentially, it’s a DNS Blacklisting solution and it can display the Domains being accessed.
To my dismay I’m seeing the VERA+ attempting calls to facebook.com on a regular basis between 20 – 70 minutes each.
The Active apps on VERA are Sercomm IP Camera, Amazon Alexa Helper, Garage Door, Foscam HD, Reator, SiteSensor and Ezlo Cameras. I just recently removed AltUI before disconnecting from the cloud services.
Any ideas on how I could track down the culprit caller?
Thanks for your consideration.
I've got a Nokia/Withings bathroom scale on which I weigh myself daily. I used to use IFTTT to push every weighing result into a Google Spreadsheet in the cloud, but now that I use MSR, I'm more interested in integrating this data into that workflow.
Has anyone figured out a way to move data from a WiFi-connected scale into the Vera environment? I don't mind trying something indirect, as for instance I've already linked the weights over to my Google Fit app.
Open to suggestions!
Recently I have been getting constant reloads on my Vera Plus running the latest 7.32 beta build. It usually starts after a 3-4 day Luup uptime and the reloads start at around 5am local time and keep going every 30 mins until I physically restart my Vera Plus (unplugging and plugging it back in). Right before a reload I see on the status bar above the modes on the homepage "cannot write user data" then after a few minutes a reload occurs. Looking into the logs I have seen mention of 03 06/21/21 8:53:18.102 JobHandler_LuaUPnP::Reload: low memory Critical 1 m_bCriticalOnly 0 dirty data 1 running 1 <0x76aa7520> almost every single time a reload happens. I have attached logs from 2 instances this morning where a reload happened. I have noticed that the OpenSprinkler plugin has been very chatty even though I have set debugging to 0, is that what is filling up temp log system?
01 06/21/21 8:45:58.123 IOPort::Connect connect -1 192.168.8.43:23 <0x6a148520>
02 06/21/21 8:45:59.031 UserData::CommitToDatabase data size 1244271 1244271 <0x7662b520>
01 06/21/21 8:45:59.333 UserData::WriteUserData saved--before move File Size: 234865 save size 234865 <0x7662b520>
02 06/21/21 8:45:59.333 UserData::TempLogFileSystemFailure start 0 <0x7662b520>
02 06/21/21 8:45:59.334 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x7662b520>
02 06/21/21 8:45:59.334 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x7662b520>
01 06/21/21 8:45:59.341 UserData::WriteUserData failed File Size: 234865 save size 234902 <0x7662b520>
02 06/21/21 8:45:59.342 UserData::TempLogFileSystemFailure start 1 <0x7662b520>
02 06/21/21 8:45:59.344 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x7662b520>
01 06/21/21 8:45:59.632 UserData::WriteUserData failed result:1 size2:234865 vs 234865 <0x7662b520>
02 06/21/21 8:45:59.632 UserData::TempLogFileSystemFailure start 1 <0x7662b520>
02 06/21/21 8:45:59.634 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x7662b520>
02 06/21/21 8:45:59.635 UserData::TempLogFileSystemFailure start 0 <0x7662b520>
02 06/21/21 8:45:59.635 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x7662b520>
02 06/21/21 8:45:59.636 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x7662b520>
06 06/21/21 8:45:59.636 Device_Variable::m_szValue_set device: 1 service: urn:micasaverde-com:serviceId:ZWaveNetwork1 variable: NetStatusID was: 1 now: 2 #hooks: 0 upnp: 0 skip: 0 v:0x1099d38/NONE duplicate:0 <0x7662b520>
06 06/21/21 8:45:59.637 Device_Variable::m_szValue_set device: 1 service: urn:micasaverde-com:serviceId:ZWaveNetwork1 variable: NetStatusText was: OK now: Resetting ZWave Network #hooks: 0 upnp: 0 skip: 0 v:0x1a02d48/NONE duplicate:0 <0x7662b520>
06 06/21/21 8:45:59.637 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeNetwork1 variable: NetStatusID was: 0 now: 3 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x7662b520>
06 06/21/21 8:45:59.638 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeNetwork1 variable: NetStatusText was: OK now: GET_LANG(resetting_zigbee_network,Resetting Zigbee Network) #hooks: 0 upnp: 0 skip: 0 v:0x12b9e60/NONE duplicate:0 <0x7662b520>
01 06/21/21 8:45:59.648 RAServerSync::SendAlert notification lost quit 1 device 50002761 servers:vera-us-oem-event12.mios.com/vera-us-oem-event11.mios.com for time 23822220 type 7 code user_data <0x7642b520>
02 06/21/21 8:46:01.381 UserData::CommitToDatabase data size 1244349 1244349 <0x770dc320>
01 06/21/21 8:46:01.675 UserData::WriteUserData saved--before move File Size: 234875 save size 234875 <0x770dc320>
02 06/21/21 8:46:01.675 UserData::TempLogFileSystemFailure start 0 <0x770dc320>
02 06/21/21 8:46:01.676 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x770dc320>
02 06/21/21 8:46:01.676 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x770dc320>
01 06/21/21 8:46:01.680 UserData::WriteUserData failed File Size: 234875 save size 234865 <0x770dc320>
02 06/21/21 8:46:01.680 UserData::TempLogFileSystemFailure start 1 <0x770dc320>
02 06/21/21 8:46:01.682 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x770dc320>
01 06/21/21 8:46:01.940 UserData::WriteUserData failed result:1 size2:234875 vs 234875 <0x770dc320>
02 06/21/21 8:46:01.941 UserData::TempLogFileSystemFailure start 1 <0x770dc320>
02 06/21/21 8:46:01.943 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x770dc320>
02 06/21/21 8:46:01.944 UserData::TempLogFileSystemFailure start 0 <0x770dc320>
02 06/21/21 8:46:01.945 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x770dc320>
02 06/21/21 8:46:01.945 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x770dc320>
50 06/21/21 8:46:03.102 luup_log:1304: VeraOpenSprinkler[1.50]: [updateFromController] error: false - nil - nil <0x72581520>
01 06/21/21 8:46:05.210 Main WatchDogRoutine: blocked - terminating 1 <0x695de520>
02 06/21/21 8:46:05.211 Dumping 40 locks <0x695de520>
02 06/21/21 8:46:05.211 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.211 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.211 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.211 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.212 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.213 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.214 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.215 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.216 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.217 OL: (0xbbc560) (>100746) Variable JobHandler_LuaUPnP.cpp l:9817 time: 4:00:00p (1624290365 s) thread: 0x6f948520 Rel: Y Got: Y <0x695de520>
02 06/21/21 8:46:05.217 finished check for exceptions <0x695de520>
02 06/21/21 8:46:05.218 OL: (0xbbc560) (>100751) Variable JobHandler_LuaUPnP.cpp l:9817 time: 4:00:00p (1624290365 s) thread: 0x6d948520 Rel: Y Got: Y <0x695de520>
2021-06-21 08:46:05 - LuaUPnP Terminated with Exit Code: 137
03 06/21/21 8:53:18.102 JobHandler_LuaUPnP::Reload: low memory Critical 1 m_bCriticalOnly 0 dirty data 1 running 1 <0x76aa7520>
01 06/21/21 8:53:18.103 luup_log:901: Tesla Car_error: Monitor awake state, failed #400 HTTP/1.1 400 BAD REQUEST !! <0x72ffd520>
02 06/21/21 8:53:18.482 UserData::CommitToDatabase data size 1244185 1244185 <0x76aa7520>
01 06/21/21 8:53:18.781 UserData::WriteUserData saved--before move File Size: 234865 save size 234865 <0x76aa7520>
02 06/21/21 8:53:18.781 UserData::TempLogFileSystemFailure start 0 <0x76aa7520>
02 06/21/21 8:53:18.781 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x76aa7520>
02 06/21/21 8:53:18.782 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x76aa7520>
01 06/21/21 8:53:18.787 UserData::WriteUserData failed File Size: 234865 save size 234875 <0x76aa7520>
02 06/21/21 8:53:18.787 UserData::TempLogFileSystemFailure start 1 <0x76aa7520>
02 06/21/21 8:53:18.789 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x76aa7520>
01 06/21/21 8:53:18.813 IOPort::Connect connect -1 192.168.8.43:23 <0x6a7c4520>
01 06/21/21 8:53:19.020 UserData::WriteUserData failed result:1 size2:234865 vs 234865 <0x76aa7520>
02 06/21/21 8:53:19.020 UserData::TempLogFileSystemFailure start 1 <0x76aa7520>
02 06/21/21 8:53:19.023 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x76aa7520>
02 06/21/21 8:53:19.027 UserData::TempLogFileSystemFailure start 0 <0x76aa7520>
02 06/21/21 8:53:19.028 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x76aa7520>
02 06/21/21 8:53:19.028 UserData::TempLogFileSystemFailure 0 res:0
(null) <0x76aa7520>
06 06/21/21 8:53:19.029 Device_Variable::m_szValue_set device: 1 service: urn:micasaverde-com:serviceId:ZWaveNetwork1 variable: NetStatusID was: 1 now: 2 #hooks: 0 upnp: 0 skip: 0 v:0x14bad80/NONE duplicate:0 <0x76aa7520>
06 06/21/21 8:53:19.029 Device_Variable::m_szValue_set device: 1 service: urn:micasaverde-com:serviceId:ZWaveNetwork1 variable: NetStatusText was: OK now: Resetting ZWave Network #hooks: 0 upnp: 0 skip: 0 v:0x1e23b10/NONE duplicate:0 <0x76aa7520>
06 06/21/21 8:53:19.033 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeNetwork1 variable: NetStatusID was: 0 now: 3 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:0 <0x76aa7520>
01 06/21/21 8:53:19.040 RAServerSync::SendAlert notification lost quit 1 device 50002761 servers:vera-us-oem-event12.mios.com/vera-us-oem-event11.mios.com for time 20546340 type 7 code user_data <0x76ca7520>
06 06/21/21 8:53:19.044 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeNetwork1 variable: NetStatusText was: OK now: GET_LANG(resetting_zigbee_network,Resetting Zigbee Network) #hooks: 0 upnp: 0 skip: 0 v:0x16dadc0/NONE duplicate:0 <0x76aa7520>
02 06/21/21 8:53:20.807 UserData::CommitToDatabase data size 1244263 1244263 <0x77759320>
01 06/21/21 8:53:21.081 UserData::WriteUserData saved--before move File Size: 234875 save size 234875 <0x77759320>
02 06/21/21 8:53:21.081 UserData::TempLogFileSystemFailure start 0 <0x77759320>
02 06/21/21 8:53:21.116 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x77759320>
02 06/21/21 8:53:21.117 UserData::TempLogFileSystemFailure 699 res:1
-rw-r--r-- 1 root root 504 Jun 26 2017 /etc/cmh/user_data.json.luup.lzo
-rw-r--r-- 1 root root 234865 Jun 21 08:53 /etc/cmh/user_data.json.lzo
-rw-r--r-- 1 root root 234996 Jun 21 08:11 /etc/cmh/user_data.json.lzo.1
-rw-r--r-- 1 root root 234930 Jun 21 08:02 /etc/cmh/user_data.json.lzo.2
-rw-r--r-- 1 root root 234968 Jun 21 07:47 /etc/cmh/user_data.json.lzo.3
-rw-r--r-- 1 root root 234658 Jun 21 07:11 /etc/cmh/user_data.json.lzo.4
-rw-r--r-- 1 root root 234909 Jun 21 06:50 /etc/cmh/user_data.json.lzo.5
-rw-r--r-- 1 root root 234875 Jun 21 08:53 /etc/cmh/user_data.json.lzo.new
<0x77759320>
02 06/21/21 8:53:21.228 UserData::TempLogFileSystemFailure start 0 <0x77759320>
02 06/21/21 8:53:21.259 UserData::TempLogFileSystemFailure (not failure, only WriteUserData) 0 <0x77759320>
02 06/21/21 8:53:21.259 UserData::TempLogFileSystemFailure 610 res:1
-rw-r--r-- 1 root root 504 Jun 26 2017 /etc/cmh/user_data.json.luup.lzo
-rw-r--r-- 1 root root 234875 Jun 21 08:53 /etc/cmh/user_data.json.lzo
-rw-r--r-- 1 root root 234865 Jun 21 08:53 /etc/cmh/user_data.json.lzo.1
-rw-r--r-- 1 root root 234996 Jun 21 08:11 /etc/cmh/user_data.json.lzo.2
-rw-r--r-- 1 root root 234930 Jun 21 08:02 /etc/cmh/user_data.json.lzo.3
-rw-r--r-- 1 root root 234968 Jun 21 07:47 /etc/cmh/user_data.json.lzo.4
-rw-r--r-- 1 root root 234658 Jun 21 07:11 /etc/cmh/user_data.json.lzo.5
<0x77759320>
06 06/21/21 8:53:21.465 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeDevice1 variable: PendingRemoveDevices was: 0024460000144655-01d8,0024460000146120-a155,00244600001467ad-a538 now: 0024460000144655-01d8,0024460000146120-a155,00244600001467ad-a538 #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:1 <0x77759320>
06 06/21/21 8:53:21.469 Device_Variable::m_szValue_set device: 2 service: urn:micasaverde-com:serviceId:ZigbeeDevice1 variable: UnknownDevices was: now: #hooks: 0 upnp: 0 skip: 0 v:(nil)/NONE duplicate:1 <0x77759320>
03 06/21/21 8:53:22.100 LuaUPNP: ending <0x77759320>
2021-06-21 08:53:22 - LuaUPnP Terminated with Exit Code: 0```
Vera account suspended for a 1000 years
-
Yeah really don't miss the old forum thanks to @DesT!
Live and let ... be.
Happy as clam with my zwave and zigbee setup honestly... and to not have had to exclude/re-include anything to get there was a major part of it, given the size of my network. -
Yeah really don't miss the old forum thanks to @DesT!
Live and let ... be.
Happy as clam with my zwave and zigbee setup honestly... and to not have had to exclude/re-include anything to get there was a major part of it, given the size of my network. -
Yeah really don't miss the old forum thanks to @DesT!
Live and let ... be.
Happy as clam with my zwave and zigbee setup honestly... and to not have had to exclude/re-include anything to get there was a major part of it, given the size of my network. -
Well that was quick/painless :). Thanks BlackCat!
@DesT - One other thing that would be handy is for code blocks to have a 'click - copy to clipboard' function. Unless I just missed that somehow as well
@Trexx said in Vera account suspended for a 1000 years:
Well that was quick/painless :). Thanks BlackCat!
@DesT - One other thing that would be handy is for code blocks to have a 'click - copy to clipboard' function. Unless I just missed that somehow as well
I would need to check that. Pretty sure for the moment there's no option for that!
-
@rafale77 I've had one device stop working. Re-interviewing it fixed it immediately.
Not got round to working out what happened but meh....
C
I had this too at the very beginning and managed to correlate it to noise in the zwave network "corrupting" the z-way device database. Strangely z-way allows for further command class discovery after interview and inclusions, which enables wrong interview settings when somehow a zwave packet passes the zwave CRC check. I have completely eliminated this problem by reducing the noise on the 900MHz band which z-way enables you to monitor.
It was part of my effort to remove all these crappy power bricks around the controller, using a USB extension cord to move the uzb away from other electronics etc... regardless of this problem, it is a good thing to do anyway to reduce errors, lower retry rates and network improve speed. These are things software can't help with. They are physical RF noise which should be minimized as much as possible. -
So this is where all the banned Vera members rejoice.. definitely will be posting here more than the toxic vera community forums
-
Welcome, but honestly, whiskey tango foxtrot? What did you say that got you banned?
Author of Multi-system Reactor and Reactor, DelayLight, Switchboard, and about a dozen other plugins that run on Vera and openLuup.
-
Welcome, but honestly, whiskey tango foxtrot? What did you say that got you banned?
-
Yup. That's why I'm being pretty aggressive about not having MSR posts over there.
-
@toggledbits Nothing yet .. you just don't know what you could say that will get you banned. Not like I am very active on those forums anyways
-
Ah, interesting... I had PM’d the OP of that thread saying that the place to get good advice on topics like that was here!
(So if they read that, I’ll be joining too.)
-
@akbooer I’m afraid you’re right. They read your pm.
I’m not banned, just joining another, perhaps more interesting forum -
He is very sensitive if anyone criticizes his baby, I'm with @akbooer but believe the wheels have already fallen off as there are few devs left on the forum.
It will be at least 2 years before there is a viable marketable product let alone any plugins to replace what will be lost when Vera goes EOL.
