The locksmith is trying to persuade me to purchase the BE-TECH K35 touchscreen lock with both Wi-Fi and Bluetooth, claiming it's better than the Yale Assure Lock 2. What are your thoughts on this? Which one would you recommend?
Here is the link to the Chinese brand BE-TECH: BE-TECH Smart Deadbolt K3S.
The other smart lock I am considering is the Schlage Encode Plus.
Thank you!
The promise of "all available devices will be supported" gave me hope for including more Zigbee devices into to my home as Vera was not a good option for Zigbee devices.
Despite the support for new devices is extremely slow, the implementation of Zigbee has a lot to wish for and it seems a low priority at Ezlo I managed to include 22 of my 23 Zigbee devices as generic. But after 2 years of devices still missing attributes and randomly/every controller reboot loosing connection to the controller and had to be power cycled to connect again, and some even dropping off the network completely without any reason, I decided to give up.
The positive outcome of all this:
I bought a Sonoff Zigbee 3.0 USB Dongle Plus and installed Zigbee2MQTT and never been happier.
Suddenly the pairing were no pain and took a few seconds per device, all my devices were recognized, all capabilities of the devices were exposed and it never misses a signal to/from a device ever.
I'm surprised how stable and configurable my new setup is. I can set device parameters, offsets, send messages handled by the bulbs them self like effects, broadcast for groups, transition time for power on/off. I can handle debounce for MQTT messages, do OTA firmware update on devices and much more! Most of this is probably standard for the common branded hubs like Hue etc but I never had one so this is new to me.
A big plus for me is the MQTT part of Zigbee2MQTT as I'm migrating as much as possible to MQTT.
My Ezlo Plus is now serving as a modified WiFi access point to my network and only have the VistaCam 1203 Doorbell still connected for evaluation. Time will tell if I ever move my Z-wave devices to it.
Conclusion:
I could really recommend both the Sonoff 3.0 USB Dongle Plus and Zigbee2MQTT to anyone going the same path!
In a quest to further stabilize my Vera before I'll move to Z-Way+openLuup or something else later this year (I'm tempted to go the Home Assistant route, since all my friends are here, apparently), I've spent a couple of days removing HTTP calls from the system and I'm now fully using the UDP sender @akbooer has written in the past, to push all variables (and custom events/request as well) to my MQTT broker, then to some code doing the actual work.
Responsiveness seems to be at its maximum now, and stability has improved. There's still a lot of code locally on my Vera, but it's mainly doing variables comparison/scenes, while all notifications and heavy logic are now running in my linux box.
So, maybe, not insisting on the sockets and just use the same UDP server is the way to go for me.
Well here we go. A slow, considered migration from Vera to something (I hope) more reliable.
Hopefully we'll end up with a decent documented process for people as right now I'm still not quite clear
Starting point:
I have a 'mature' Mios set up running on an extrooted Vera Plus with roughly 100 devices, both physical and virtual
Integration with Alexa both voice control and TTS
iPhones for Geolocation
Volumio devices for music playing around the house.
I have no user defined scenes, all automation is run from Reactor.
My impetus is final dissatisfaction with the quality of UI7 software delivery and operational rigour (for full disclosure I am a senior IT Operations leader with circa 20 years experience delivering properly stable systems, so I probably have un-realistic expectations )
So initial steps:
Raspberry Pi 3 B+ (I think this is my 5, and 6th Pi in total. I may have a problem)
Raspbian
OpenLuup
Verabridge
That I think is stage 1
C
I am a Electrician. I installed hundreds of smart devices for others prior to having my own home automation. In 2013 I bought a new house and decided to make it smart. I did some homework and settled on Z-wave and VeraPlus.
My installation comprises of
25 Z-wave dimmer/switch inserts
3 Z-wave door sensors
10 sonoff devices(basics,TH16 and Mini) ,
4 Tuya(lamps and RGB strips) ,
6 shellys(connected to motion sensors and 2 controlling dead DIY bolts )
3 Amazon Dots(gen2)
2 Broadlink (RMPro's)
4 DIY RF Venetian Blinds
2 Multi button DIY remotes
1 NVR
1 Network drive/Media server/ftp server.
1 smart thermostat heating and hot water
4 wired 240v/battery Aico smoke and heat detectors (connect to zwave via Relays)
1 robot hover.
1 Siren
Node-red server running on android.
Testing openluup on android.
Automate App running on andorid Boxes/phones.
All tv's are connected to android boxes.
No windows PC.
Debian running on android box.
Plugins Reactor, AlexaTTS, Switchboard and Virtual HTTP Switch.
I can control all of my devices from anyone of these platforms Vera/OpenLuup, Node-red, Automate(phone/tv box) or Alexa.
All devices have a standard/manual switch for anyone to control, and can be controlled even if my VeraPlus stopped working or internet out. My system is stable and may get a luup reload every couple of weeks.
None of my sonoff's or tuya have been flashed. I found Shelly very late into game and will be using these more now i found them, as they offer local control.
I have some coding knowledge from the 90's, but have never worked in the industry.
Well, if I see further, it's because I stand of the shoulders of giants. I've got where I got because of the experts here. I started about 15 years ago with some really basic X10 stuff. When we moved in 2011 for some reason it simply would not work in the new house, so z-wave was the thing. Vera lite then Vera Plus.
I'm a child of the 70s. I want the car on the drive to be KITT and my lounge a cross between the bridge of the enterprise and the Lars farm on Tattoine.
Not there yet, but with about 250 devices (virtual and real) things are fun (when they work!)
The absolute killer app for me is Alexa bi directional speech. To the extent that I've walked into hotel rooms and said 'Alexa turn the lights on....'
I'm within a spit of never buying another control and doing everything via Alexa and Reactor (had to drop that in)
So that's pretty much me.
C
My migration from Vera, or what I did on my holidays
Blogs
105
Posts
6
Posters
27.0k
Views
7
Watching
-
Hmm will wait for @akbooer on this one. I have never seen this and since I no longer have a verabridge or a vera, I can't even check.
Try copying the temperature xml file from the vera and put it in openLuup?Edit: I just checked, and mine was definitely imported. It maybe a chicken and egg problem caused by a file import failure. Maybe try importing the entire /etc/cmh-lu and /etc/cmh-ludl content and dump them in /etc/cmh-ludl/files on openLuup. I suspect something has changed at some point on the vera firmware making this import function fail.
-
Hi Catman,
Things you may need to install as well: cjson, dkjson, bit,.... jeez, I wish i made notes the last time i installed openLuup
Cheers Rene
@mrFarmer said in My migration from Vera, or what I did on my holidays:
Hi Catman,
Things you may need to install as well: cjson, dkjson, bit,.... jeez, I wish i made notes the last time i installed openLuup
Cheers Rene
Rather why I'm doing this
So I have cjson and dkjson
Did you mean something like 'bit' or was it a typo of 'but'?
Nothing is different. I have deleted and re-installed the VeraBridge. Still says 'No Vera' even with the correct IP address, and only about 15 devices.
Cheers
C
-
Rather strange as your last error seem to indicate that the vera API returned an empty device table... Why would that be? Failing to decode json should have prompted another error but you already have that covered. All the files are in your openLuup installation folder right? (Mine is in /etc/cmh-ludl)
-
-
OpenLuup won’t decompress the lzo files. Therefore you would need to download them through UI7, one by one and then upload them in the openLuup installation. This is what the getverafiles does...
Otherwise you could also SCP into the vera and run an lzo decompress of all the files before downloading them.
The primary concern here though is why openLuup gets an empty device table from the vera now. It seems like you initially did get devices right? That’s why it was failing to create 10009 due to the missing xml file. This meant that it actually connected and that your vera device id 9 is a temperature sensor which openLuup was trying to mirror but was missing a file to do so.
Now your error seems to be altogether different: It seems to not see the vera’s returned json file and that puzzles me.To decompress the files on the vera the command is:
pluto-lzo -d file.lzo newfilename -
It also has the rooms correctly cloned, though none of the devices that do exist are in the correct rooms.
Assuming that the devices are created in numerical order makes no sense either as I have 10061 in OpenLuup for example
I also have 10041 which works, but is in the wrong room (a simple switch)
1009 is the temperature reading of a Fibaro 3-in-1Migh highest ID on Openluup is 79, the control for my boiler, everything from that is missing. Everything down is there but faulty.
I think, given that part of the purpose here is to create a migration guide, I'll possess my sole in patience for @akbooer
It's probably user error
C
-
I think they are missing because the xml files for these devices are missing from the openLuup installation which is the first problem you reported. This appears to indicate that the verabridge did connect. Why it failed to import the xml verafiles and why it subsequently shows that it can't connect is what is so strange.
-
Well I'm going to stop now before I get too far ahead of myself. I'm quite au fait with Linux and so far simples.
(I'm doing this on an Intel NUC I have lying around just for simplicity before the Pi arrives next week)
Assuming you have a nice, up to date Debian install, and using the documentation here:
openLuup/Documentation/openLuup User Guide.pdf at master · akbooer/openLuup
a pure-Lua open-source emulation of the Vera Luup environment - akbooer/openLuup
First install Lua:
# apt-get update # apt-get install lua5.1 # apt-get install lua-socket # apt-get install lua-filesystem # apt-get install lua-secCreate your cmh-ludl directory. I used /etc/cmh-ludl for backwards compatability with Vera
#mkdir /etc/cmh-ludlcd into that directory and then
#wget https://github.com/akbooer/openLuup/raw/master/Utilities/openLuup_install.luafrom the same directory:
# lua5.1 openLuup_install.luaI had a momentary gotcha as lua5.1 is not in my $PATH. I might add it later but I had to use:
#/usr/bin/lua openLuup_install.luaAssuming that all looks good check
http://you_ip_address:3480 with a browser and be amazed that AltUI is already up and running.
Next steps are to make OpenLuup start at boot. There are several documented ways. I went with systemctl for consistency.
This is documented here
http://forum.micasaverde.com/index.php/topic,48431.0.htmlHowever:
sudo nano /etc/cmh-ludl/run_openLuup.shThen
#!/bin/bash echo "Starting openLuup server" echo "To see tail of logfile: tail -f ./out.log" cd /etc/cmh-ludl sudo rm ./out.log nohup ./openLuup_reload >> out.log 2>&1 &Make it executable
sudo chmod +x run_openLuup.shCreate the service
sudo nano /etc/systemd/system/openluup.serviceAdd this code
[Unit] Description=openLuup and AltUI Server for Vera 3 Wants=network.target After=network.target [Service] Type=forking WorkingDirectory=/etc/cmh-ludl ExecStart=/bin/bash /etc/cmh-ludl/run_openLuup.sh [Install] WantedBy=multi-user.targetThen enable it and make it so it starts at boot:
sudo systemctl enable openluup sudo systemctl start openluuReboot to check and it's all good
So far so simple!
C
@CatmanV2 said in My migration from Vera, or what I did on my holidays:
http://you_ip_address:3480 with a browser and be amazed that AltUI is already up and running.
@CatmanV2 said in My migration from Vera, or what I did on my holidays:
I shall google while I wait for the esteemed @akbooer to enlighten me
Not seen this before, either. I’ll check the code, but, meantime, it’s not an issue with security settings on Vera, is it? Need to allow some ‘unsafe’ actions, IIRC.
-
Hi Catman,
Things you may need to install as well: cjson, dkjson, bit,.... jeez, I wish i made notes the last time i installed openLuup
Cheers Rene
-
This is the moment to look at the logs:
- Startup log
- Standard log, at the the start of it, after a system startup.
These most easily available from the openLuup console Logs menu, or directly from:
and
...I'm confused by the 'Vera is running but No Vera shown'.
-
Thanks @akbooer
Startup log and Lua log don't tell me anything that I find useful
2020-06-19 15:57:41.027 :: openLuup STARTUP :: /etc/cmh-ludl 2020-06-19 15:57:41.027 openLuup.init:: version 2020.05.01 @akbooer 2020-06-19 15:57:41.041 openLuup.scheduler:: version 2020.01.25 @akbooer 2020-06-19 15:57:41.051 openLuup.wsapi:: version 2019.08.12 @akbooer 2020-06-19 15:57:41.051 openLuup.servlet:: version 2020.01.29 @akbooer 2020-06-19 15:57:41.051 openLuup.client:: version 2019.10.14 @akbooer 2020-06-19 15:57:41.052 openLuup.io:: version 2019.11.29 @akbooer 2020-06-19 15:57:41.052 openLuup.server:: version 2020.03.20 @akbooer 2020-06-19 15:57:41.055 openLuup.scenes:: version 2020.03.16 @akbooer 2020-06-19 15:57:41.056 openLuup.chdev:: version 2020.03.07 @akbooer 2020-06-19 15:57:41.056 openLuup.userdata:: version 2020.03.31 @akbooer 2020-06-19 15:57:41.057 openLuup.requests:: version 2020.04.15 @akbooer 2020-06-19 15:57:41.057 openLuup.gateway:: version 2020.03.08 @akbooer 2020-06-19 15:57:41.058 openLuup.smtp:: version 2018.04.12 @akbooer 2020-06-19 15:57:41.060 openLuup.historian:: version 2020.02.12 @akbooer 2020-06-19 15:57:41.061 openLuup.luup:: version 2020.03.21 @akbooer 2020-06-19 15:57:41.061 openLuup.pop3:: version 2018.04.23 @akbooer 2020-06-19 15:57:41.062 openLuup.compression:: version 2016.06.30 @akbooer 2020-06-19 15:57:41.062 openLuup.timers:: version 2019.05.03 @akbooer 2020-06-19 15:57:41.062 openLuup.logs:: version 2018.03.25 @akbooer 2020-06-19 15:57:41.062 openLuup.json:: version 2020.05.20 @akbooer 2020-06-19 15:57:41.062 openLuup.init:: using Cjson 2.1.0 for fast decoding 2020-06-19 15:57:41.062 luup.create_device:: [1] D_ZWaveNetwork.xml / / () 2020-06-19 15:57:41.062 openLuup.chdev:: ERROR: unable to read XML file I_ZWave.xml 2020-06-19 15:57:41.068 luup.create_device:: [2] D_openLuup.xml / I_openLuup.xml / D_openLuup.json (openLuup) 2020-06-19 15:57:41.068 openLuup.init:: loading configuration user_data.json 2020-06-19 15:57:41.068 openLuup.userdata:: loading user_data json... 2020-06-19 15:57:41.072 luup.variable_set:: 2.openLuup.HouseMode was: EMPTY now: 1 #hooks:0 2020-06-19 15:57:41.072 openLuup.userdata:: loading rooms... 2020-06-19 15:57:41.072 openLuup.userdata:: room#1 'MiOS-50103066' 2020-06-19 15:57:41.072 openLuup.userdata:: room#2 'Garden' 2020-06-19 15:57:41.072 openLuup.userdata:: room#3 'Driveway' 2020-06-19 15:57:41.072 openLuup.userdata:: room#4 'Hall' 2020-06-19 15:57:41.072 openLuup.userdata:: room#5 'Living Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#6 'Server Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#7 'Porch' 2020-06-19 15:57:41.072 openLuup.userdata:: room#8 'ReactorCore' 2020-06-19 15:57:41.072 openLuup.userdata:: room#9 'Garage' 2020-06-19 15:57:41.072 openLuup.userdata:: room#10 'Master Bedroom' 2020-06-19 15:57:41.072 openLuup.userdata:: room#11 'Media_Centre' 2020-06-19 15:57:41.072 openLuup.userdata:: room#12 'Office' 2020-06-19 15:57:41.072 openLuup.userdata:: room#13 'X-Lab' 2020-06-19 15:57:41.072 openLuup.userdata:: room#14 'Dining Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#15 'Greenhouse' 2020-06-19 15:57:41.072 openLuup.userdata:: room#16 'Kitchen' 2020-06-19 15:57:41.072 openLuup.userdata:: ...room loading completed 2020-06-19 15:57:41.072 openLuup.userdata:: loading devices... 2020-06-19 15:57:41.073 luup.create_device:: [1] D_ZWaveNetwork.xml / X / (urn:schemas-micasaverde-com:device:ZWaveNetwork:1) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.starts' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.altui_split' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.template' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.trim' (a function value) 2020-06-19 15:57:41.113 luup.create_device:: [3] D_ALTUI.xml / I_ALTUI.xml / D_ALTUI_UI7.json (urn:schemas-upnp-org:device:altui:1) 2020-06-19 15:57:41.117 luup.create_device:: [4] D_AltAppStore.xml / I_AltAppStore.xml / D_AltAppStore.json (urn:schemas-upnp-org:device:AltAppStore:1) 2020-06-19 15:57:41.123 luup.create_device:: [7] D_VeraBridge.xml / I_VeraBridge.xml / D_VeraBridge.json (VeraBridge) 2020-06-19 15:57:41.123 luup.create_device:: [10002] D_ZigbeeNetwork.xml / / () 2020-06-19 15:57:41.123 openLuup.chdev:: ERROR: unable to read XML file D_ZigbeeNetwork.xml 2020-06-19 15:57:41.123 luup.create_device:: [10003] D_BluetoothNetwork.xml / / () 2020-06-19 15:57:41.123 openLuup.chdev:: ERROR: unable to read XML file D_BluetoothNetwork.xml 2020-06-19 15:57:41.123 luup.create_device:: [10004] D_SceneController1.xml / / () 2020-06-19 15:57:41.124 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.124 luup.create_device:: [10006] D_SceneController1.xml / / () 2020-06-19 15:57:41.124 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.125 luup.create_device:: [10007] D_SceneController1.xml / / () 2020-06-19 15:57:41.125 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.126 luup.create_device:: [10008] D_MotionSensor1.xml / X / D_MotionSensorWithTamper1.json (urn:schemas-micasaverde-com:device:MotionSensor:1) 2020-06-19 15:57:41.127 luup.create_device:: [10009] D_TemperatureSensor1.xml / / () 2020-06-19 15:57:41.127 openLuup.chdev:: ERROR: unable to read XML file D_TemperatureSensor1.xml 2020-06-19 15:57:41.127 luup.create_device:: [10010] D_LightSensor1.xml / / () 2020-06-19 15:57:41.127 openLuup.chdev:: ERROR: unable to read XML file D_LightSensor1.xml 2020-06-19 15:57:41.130 luup.create_device:: [10011] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.131 luup.create_device:: [10015] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.131 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.132 luup.create_device:: [10018] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.134 luup.create_device:: [10019] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.136 luup.create_device:: [10020] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.137 luup.create_device:: [10023] D_ALTUI.xml / X / D_ALTUI_UI7.json (urn:schemas-upnp-org:device:altui:1) 2020-06-19 15:57:41.138 luup.create_device:: [10026] D_DayTime.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DayTime.xml 2020-06-19 15:57:41.138 luup.create_device:: [10027] D_HouseModes.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_HouseModes.xml 2020-06-19 15:57:41.138 luup.create_device:: [10031] D_DigitalSecurityCamera2.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-19 15:57:41.138 luup.create_device:: [10033] D_DigitalSecurityCamera2.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-19 15:57:41.140 luup.create_device:: [10037] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.141 luup.create_device:: [10041] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.143 luup.create_device:: [10057] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.144 luup.create_device:: [10061] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.144 luup.create_device:: [10062] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.144 luup.create_device:: [10079] D_Heater1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_Heater1.xml 2020-06-19 15:57:41.145 openLuup.userdata:: loading scenes... 2020-06-19 15:57:41.145 openLuup.userdata:: number of scenes = 0 2020-06-19 15:57:41.145 openLuup.userdata:: ...scene loading completed 2020-06-19 15:57:41.145 openLuup.userdata:: loading installed plugin info... 2020-06-19 15:57:41.145 openLuup.userdata:: [openLuup] openLuup (20.5.22) 2020-06-19 15:57:41.145 openLuup.userdata:: [AltAppStore] Alternate App Store (20.3.30) 2020-06-19 15:57:41.145 openLuup.userdata:: [VeraBridge] VeraBridge (20.4.30) 2020-06-19 15:57:41.145 openLuup.userdata:: [8246] Alternate UI (2.49b.) 2020-06-19 15:57:41.145 openLuup.userdata:: [Z-Way] Z-Way (not.installed) 2020-06-19 15:57:41.145 openLuup.userdata:: [Arduino] MySensors (not.installed) 2020-06-19 15:57:41.145 openLuup.userdata:: ...user_data loading completed 2020-06-19 15:57:41.145 openLuup.init:: running _openLuup_STARTUP_ 2020-06-19 15:57:41.145 luup_log:0: startup code completed 2020-06-19 15:57:41.145 openLuup.init:: init phase completed 2020-06-19 15:57:41.145 :: openLuup LOG ROTATION :: (runtime 0.0 days)Is the start up log. There are no immediate errrors in the Lua log, but happy to poke it.
What I mean by 'No Vera shown' is that the VeraBridge insists that there no Vera on the ip address:
I'd attach a screenshot but I can't see how!
C
The Ex-Vera abuser know as CatmanV2.....
-
Thanks @akbooer
Startup log and Lua log don't tell me anything that I find useful
2020-06-19 15:57:41.027 :: openLuup STARTUP :: /etc/cmh-ludl 2020-06-19 15:57:41.027 openLuup.init:: version 2020.05.01 @akbooer 2020-06-19 15:57:41.041 openLuup.scheduler:: version 2020.01.25 @akbooer 2020-06-19 15:57:41.051 openLuup.wsapi:: version 2019.08.12 @akbooer 2020-06-19 15:57:41.051 openLuup.servlet:: version 2020.01.29 @akbooer 2020-06-19 15:57:41.051 openLuup.client:: version 2019.10.14 @akbooer 2020-06-19 15:57:41.052 openLuup.io:: version 2019.11.29 @akbooer 2020-06-19 15:57:41.052 openLuup.server:: version 2020.03.20 @akbooer 2020-06-19 15:57:41.055 openLuup.scenes:: version 2020.03.16 @akbooer 2020-06-19 15:57:41.056 openLuup.chdev:: version 2020.03.07 @akbooer 2020-06-19 15:57:41.056 openLuup.userdata:: version 2020.03.31 @akbooer 2020-06-19 15:57:41.057 openLuup.requests:: version 2020.04.15 @akbooer 2020-06-19 15:57:41.057 openLuup.gateway:: version 2020.03.08 @akbooer 2020-06-19 15:57:41.058 openLuup.smtp:: version 2018.04.12 @akbooer 2020-06-19 15:57:41.060 openLuup.historian:: version 2020.02.12 @akbooer 2020-06-19 15:57:41.061 openLuup.luup:: version 2020.03.21 @akbooer 2020-06-19 15:57:41.061 openLuup.pop3:: version 2018.04.23 @akbooer 2020-06-19 15:57:41.062 openLuup.compression:: version 2016.06.30 @akbooer 2020-06-19 15:57:41.062 openLuup.timers:: version 2019.05.03 @akbooer 2020-06-19 15:57:41.062 openLuup.logs:: version 2018.03.25 @akbooer 2020-06-19 15:57:41.062 openLuup.json:: version 2020.05.20 @akbooer 2020-06-19 15:57:41.062 openLuup.init:: using Cjson 2.1.0 for fast decoding 2020-06-19 15:57:41.062 luup.create_device:: [1] D_ZWaveNetwork.xml / / () 2020-06-19 15:57:41.062 openLuup.chdev:: ERROR: unable to read XML file I_ZWave.xml 2020-06-19 15:57:41.068 luup.create_device:: [2] D_openLuup.xml / I_openLuup.xml / D_openLuup.json (openLuup) 2020-06-19 15:57:41.068 openLuup.init:: loading configuration user_data.json 2020-06-19 15:57:41.068 openLuup.userdata:: loading user_data json... 2020-06-19 15:57:41.072 luup.variable_set:: 2.openLuup.HouseMode was: EMPTY now: 1 #hooks:0 2020-06-19 15:57:41.072 openLuup.userdata:: loading rooms... 2020-06-19 15:57:41.072 openLuup.userdata:: room#1 'MiOS-50103066' 2020-06-19 15:57:41.072 openLuup.userdata:: room#2 'Garden' 2020-06-19 15:57:41.072 openLuup.userdata:: room#3 'Driveway' 2020-06-19 15:57:41.072 openLuup.userdata:: room#4 'Hall' 2020-06-19 15:57:41.072 openLuup.userdata:: room#5 'Living Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#6 'Server Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#7 'Porch' 2020-06-19 15:57:41.072 openLuup.userdata:: room#8 'ReactorCore' 2020-06-19 15:57:41.072 openLuup.userdata:: room#9 'Garage' 2020-06-19 15:57:41.072 openLuup.userdata:: room#10 'Master Bedroom' 2020-06-19 15:57:41.072 openLuup.userdata:: room#11 'Media_Centre' 2020-06-19 15:57:41.072 openLuup.userdata:: room#12 'Office' 2020-06-19 15:57:41.072 openLuup.userdata:: room#13 'X-Lab' 2020-06-19 15:57:41.072 openLuup.userdata:: room#14 'Dining Room' 2020-06-19 15:57:41.072 openLuup.userdata:: room#15 'Greenhouse' 2020-06-19 15:57:41.072 openLuup.userdata:: room#16 'Kitchen' 2020-06-19 15:57:41.072 openLuup.userdata:: ...room loading completed 2020-06-19 15:57:41.072 openLuup.userdata:: loading devices... 2020-06-19 15:57:41.073 luup.create_device:: [1] D_ZWaveNetwork.xml / X / (urn:schemas-micasaverde-com:device:ZWaveNetwork:1) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.starts' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.altui_split' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.template' (a function value) 2020-06-19 15:57:41.113 openLuup.scheduler.sandbox:: device 3 defined 'string.trim' (a function value) 2020-06-19 15:57:41.113 luup.create_device:: [3] D_ALTUI.xml / I_ALTUI.xml / D_ALTUI_UI7.json (urn:schemas-upnp-org:device:altui:1) 2020-06-19 15:57:41.117 luup.create_device:: [4] D_AltAppStore.xml / I_AltAppStore.xml / D_AltAppStore.json (urn:schemas-upnp-org:device:AltAppStore:1) 2020-06-19 15:57:41.123 luup.create_device:: [7] D_VeraBridge.xml / I_VeraBridge.xml / D_VeraBridge.json (VeraBridge) 2020-06-19 15:57:41.123 luup.create_device:: [10002] D_ZigbeeNetwork.xml / / () 2020-06-19 15:57:41.123 openLuup.chdev:: ERROR: unable to read XML file D_ZigbeeNetwork.xml 2020-06-19 15:57:41.123 luup.create_device:: [10003] D_BluetoothNetwork.xml / / () 2020-06-19 15:57:41.123 openLuup.chdev:: ERROR: unable to read XML file D_BluetoothNetwork.xml 2020-06-19 15:57:41.123 luup.create_device:: [10004] D_SceneController1.xml / / () 2020-06-19 15:57:41.124 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.124 luup.create_device:: [10006] D_SceneController1.xml / / () 2020-06-19 15:57:41.124 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.125 luup.create_device:: [10007] D_SceneController1.xml / / () 2020-06-19 15:57:41.125 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-19 15:57:41.126 luup.create_device:: [10008] D_MotionSensor1.xml / X / D_MotionSensorWithTamper1.json (urn:schemas-micasaverde-com:device:MotionSensor:1) 2020-06-19 15:57:41.127 luup.create_device:: [10009] D_TemperatureSensor1.xml / / () 2020-06-19 15:57:41.127 openLuup.chdev:: ERROR: unable to read XML file D_TemperatureSensor1.xml 2020-06-19 15:57:41.127 luup.create_device:: [10010] D_LightSensor1.xml / / () 2020-06-19 15:57:41.127 openLuup.chdev:: ERROR: unable to read XML file D_LightSensor1.xml 2020-06-19 15:57:41.130 luup.create_device:: [10011] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.131 luup.create_device:: [10015] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.131 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.132 luup.create_device:: [10018] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.134 luup.create_device:: [10019] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.136 luup.create_device:: [10020] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.137 luup.create_device:: [10023] D_ALTUI.xml / X / D_ALTUI_UI7.json (urn:schemas-upnp-org:device:altui:1) 2020-06-19 15:57:41.138 luup.create_device:: [10026] D_DayTime.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DayTime.xml 2020-06-19 15:57:41.138 luup.create_device:: [10027] D_HouseModes.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_HouseModes.xml 2020-06-19 15:57:41.138 luup.create_device:: [10031] D_DigitalSecurityCamera2.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-19 15:57:41.138 luup.create_device:: [10033] D_DigitalSecurityCamera2.xml / / () 2020-06-19 15:57:41.138 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-19 15:57:41.140 luup.create_device:: [10037] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.141 luup.create_device:: [10041] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.143 luup.create_device:: [10057] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-19 15:57:41.144 luup.create_device:: [10061] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.144 luup.create_device:: [10062] D_DimmableLight1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-19 15:57:41.144 luup.create_device:: [10079] D_Heater1.xml / / () 2020-06-19 15:57:41.144 openLuup.chdev:: ERROR: unable to read XML file D_Heater1.xml 2020-06-19 15:57:41.145 openLuup.userdata:: loading scenes... 2020-06-19 15:57:41.145 openLuup.userdata:: number of scenes = 0 2020-06-19 15:57:41.145 openLuup.userdata:: ...scene loading completed 2020-06-19 15:57:41.145 openLuup.userdata:: loading installed plugin info... 2020-06-19 15:57:41.145 openLuup.userdata:: [openLuup] openLuup (20.5.22) 2020-06-19 15:57:41.145 openLuup.userdata:: [AltAppStore] Alternate App Store (20.3.30) 2020-06-19 15:57:41.145 openLuup.userdata:: [VeraBridge] VeraBridge (20.4.30) 2020-06-19 15:57:41.145 openLuup.userdata:: [8246] Alternate UI (2.49b.) 2020-06-19 15:57:41.145 openLuup.userdata:: [Z-Way] Z-Way (not.installed) 2020-06-19 15:57:41.145 openLuup.userdata:: [Arduino] MySensors (not.installed) 2020-06-19 15:57:41.145 openLuup.userdata:: ...user_data loading completed 2020-06-19 15:57:41.145 openLuup.init:: running _openLuup_STARTUP_ 2020-06-19 15:57:41.145 luup_log:0: startup code completed 2020-06-19 15:57:41.145 openLuup.init:: init phase completed 2020-06-19 15:57:41.145 :: openLuup LOG ROTATION :: (runtime 0.0 days)Is the start up log. There are no immediate errrors in the Lua log, but happy to poke it.
What I mean by 'No Vera shown' is that the VeraBridge insists that there no Vera on the ip address:
I'd attach a screenshot but I can't see how!
C
@CatmanV2 said in My migration from Vera, or what I did on my holidays:
There are no immediate errrors in the Lua log, but happy to poke it.
It’s not errors that I’m specifically looking for just now, but startup sequences and versions. The first few hundred lines should suffice.
-
Whatever you say, boss. this was after a Luup reload.
2020-06-20 20:40:04.474 :: openLuup LOG ROTATION :: (runtime 0.0 days) 2020-06-20 20:40:04.474 openLuup.init:: init phase completed 2020-06-20 20:40:04.474 openLuup.io.server:: starting HTTP:3480 server on port: 3480 tcp{server}: 0x2683d34 2020-06-20 20:40:04.474 openLuup.io.server:: starting SMTP server on port: 2525 tcp{server}: 0x2685da4 2020-06-20 20:40:04.474 openLuup.io.server:: starting POP3 server on port: 11011 tcp{server}: 0x2688224 2020-06-20 20:40:04.475 openLuup.historian:: starting data historian 2020-06-20 20:40:04.475 openLuup.historian:: using memory cache size (per-variable): 1024 2020-06-20 20:40:04.475 openLuup.scheduler:: starting 2020-06-20 20:40:04.475 openLuup.scheduler:: [2] openLuup device startup 2020-06-20 20:40:04.475 luup_log:2: v20.5.22 2020-06-20 20:40:04.475 luup_log:2: sync in 115.5 s 2020-06-20 20:40:04.475 luup.variable_watch:: callback=housemode_watcher, watching=2.openLuup.HouseMode 2020-06-20 20:40:04.475 luup.register_handler:: global_function_name=openLuup_email, request=openLuup@openLuup.local 2020-06-20 20:40:04.475 luup.register_handler:: global_function_name=openLuup_images, request=images@openLuup.local 2020-06-20 20:40:04.475 luup.register_handler:: global_function_name=openLuup_events, request=events@openLuup.local 2020-06-20 20:40:04.475 luup.register_handler:: global_function_name=openLuup_mailbox, request=mail@openLuup.local 2020-06-20 20:40:04.475 luup.chdev.append:: [AltAppStore] Alternate App Store 2020-06-20 20:40:04.475 luup.chdev.sync:: [2] openLuup, syncing children 2020-06-20 20:40:04.476 luup_log:2: 3Mb, 0.1%cpu, 0.0days 2020-06-20 20:40:04.476 openLuup.scheduler:: [2] openLuup device startup completed: status=true, msg=sync in 115.5 s, name=L_openLuup 2020-06-20 20:40:04.476 openLuup.scheduler:: [3] Alternate UI device startup 2020-06-20 20:40:04.476 luup_log:3: ALTUI: initstatus(3) starting version: v2.49b 2020-06-20 20:40:04.476 openLuup.scheduler:: [3] Alternate UI device startup completed: status=, msg=, name= 2020-06-20 20:40:04.476 openLuup.scheduler:: [7] VeraBridge device startup 2020-06-20 20:40:04.476 luup_log:7: VeraBridge 2020-06-20 20:40:04.476 luup_log:7: 2020.04.30 2020-06-20 20:40:04.476 luup_log:7: 192.168.70.6 2020-06-20 20:40:04.476 luup_log:7: device clone numbering starts at 10000 2020-06-20 20:40:04.476 luup_log:7: VeraBridge maps remote Zwave controller 2020-06-20 20:40:04.476 luup_log:7: v20.4.30 2020-06-20 20:40:04.644 luup_log:7: Vera info received! 2020-06-20 20:40:04.644 luup_log:7: MiOS-50103066 2020-06-20 20:40:04.644 luup_log:7: new room number: 1 2020-06-20 20:40:04.644 luup_log:7: PK_AccessPoint = 50103066 2020-06-20 20:40:04.644 luup_log:7: BuildVersion = *1.7.4833* 2020-06-20 20:40:04.644 luup_log:7: number of remote devices = 117 2020-06-20 20:40:04.644 luup.create_device:: [1] D_ZWaveNetwork.xml / X / (urn:schemas-micasaverde-com:device:ZWaveNetwork:1) 2020-06-20 20:40:04.645 luup.create_device:: [10002] D_ZigbeeNetwork.xml / / () 2020-06-20 20:40:04.645 openLuup.chdev:: ERROR: unable to read XML file D_ZigbeeNetwork.xml 2020-06-20 20:40:04.645 luup.create_device:: [10003] D_BluetoothNetwork.xml / / () 2020-06-20 20:40:04.645 openLuup.chdev:: ERROR: unable to read XML file D_BluetoothNetwork.xml 2020-06-20 20:40:04.645 luup.create_device:: [10004] D_SceneController1.xml / / () 2020-06-20 20:40:04.645 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-20 20:40:04.646 luup.create_device:: [10006] D_SceneController1.xml / / () 2020-06-20 20:40:04.646 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-20 20:40:04.646 luup.create_device:: [10007] D_SceneController1.xml / / () 2020-06-20 20:40:04.646 openLuup.chdev:: ERROR: unable to read XML file D_SceneController1.xml 2020-06-20 20:40:04.648 luup.create_device:: [10008] D_MotionSensor1.xml / X / D_MotionSensorWithTamper1.json (urn:schemas-micasaverde-com:device:MotionSensor:1) 2020-06-20 20:40:04.648 luup.create_device:: [10009] D_TemperatureSensor1.xml / / () 2020-06-20 20:40:04.648 openLuup.chdev:: ERROR: unable to read XML file D_TemperatureSensor1.xml 2020-06-20 20:40:04.649 luup.create_device:: [10010] D_LightSensor1.xml / / () 2020-06-20 20:40:04.649 openLuup.chdev:: ERROR: unable to read XML file D_LightSensor1.xml 2020-06-20 20:40:04.650 luup.create_device:: [10011] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.650 luup.create_device:: [10015] D_DimmableLight1.xml / / () 2020-06-20 20:40:04.650 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-20 20:40:04.652 luup.create_device:: [10018] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.654 luup.create_device:: [10019] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.655 luup.create_device:: [10020] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.657 luup.create_device:: [10023] D_ALTUI.xml / X / D_ALTUI_UI7.json (urn:schemas-upnp-org:device:altui:1) 2020-06-20 20:40:04.657 luup.create_device:: [10026] D_DayTime.xml / / () 2020-06-20 20:40:04.657 openLuup.chdev:: ERROR: unable to read XML file D_DayTime.xml 2020-06-20 20:40:04.657 luup.create_device:: [10027] D_HouseModes.xml / / () 2020-06-20 20:40:04.657 openLuup.chdev:: ERROR: unable to read XML file D_HouseModes.xml 2020-06-20 20:40:04.657 luup.create_device:: [10031] D_DigitalSecurityCamera2.xml / / () 2020-06-20 20:40:04.657 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-20 20:40:04.658 luup.create_device:: [10033] D_DigitalSecurityCamera2.xml / / () 2020-06-20 20:40:04.658 openLuup.chdev:: ERROR: unable to read XML file D_DigitalSecurityCamera2.xml 2020-06-20 20:40:04.659 luup.create_device:: [10037] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.661 luup.create_device:: [10041] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.662 luup.create_device:: [10057] D_BinaryLight1.xml / X / D_BinaryLight1.json (urn:schemas-upnp-org:device:BinaryLight:1) 2020-06-20 20:40:04.663 luup.create_device:: [10061] D_DimmableLight1.xml / / () 2020-06-20 20:40:04.663 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-20 20:40:04.663 luup.create_device:: [10062] D_DimmableLight1.xml / / () 2020-06-20 20:40:04.663 openLuup.chdev:: ERROR: unable to read XML file D_DimmableLight1.xml 2020-06-20 20:40:04.663 luup.create_device:: [10079] D_Heater1.xml / / () 2020-06-20 20:40:04.663 openLuup.chdev:: ERROR: unable to read XML file D_Heater1.xml 2020-06-20 20:40:04.664 luup.create_device:: [10080] D_Heater1.xml / / () 2020-06-20 20:40:04.664 openLuup.chdev:: ERROR: unable to read XML file D_Heater1.xml 2020-06-20 20:40:04.664 openLuup.context_switch:: ERROR: [dev #7] ./openLuup/devices.lua:538: table index is nil 2020-06-20 20:40:04.664 openLuup.scheduler:: job aborted : ./openLuup/devices.lua:538: table index is nil 2020-06-20 20:40:04.664 openLuup.scheduler:: [4] Alternate App Store device startup 2020-06-20 20:40:04.664 luup_log:4: AltAppStore : starting... 2020-06-20 20:40:04.664 luup.variable_set:: 4.urn:upnp-org:serviceId:altui1.DisplayLine1 was: AltAppStore now: AltAppStore #hooks:0 2020-06-20 20:40:04.664 luup.variable_set:: 4.urn:upnp-org:serviceId:altui1.DisplayLine2 was: now: #hooks:0 2020-06-20 20:40:04.664 luup_log:4: AltAppStore : v20.3.30 2020-06-20 20:40:04.664 luup.set_failure:: status = 0 2020-06-20 20:40:04.664 luup.variable_set:: 4.urn:micasaverde-com:serviceId:HaDevice1.CommFailure was: 0 now: 0 #hooks:0 2020-06-20 20:40:04.664 luup.variable_set:: 4.urn:micasaverde-com:serviceId:HaDevice1.CommFailureTime was: 0 now: 0 #hooks:0 2020-06-20 20:40:04.664 openLuup.scheduler:: [4] Alternate App Store device startup completed: status=true, msg=OK, name=AltAppStore 2020-06-20 20:40:05.372 openLuup.io.server:: HTTP:3480 connection from 192.168.70.251 tcp{client}: 0x27493a4 2020-06-20 20:40:05.373 openLuup.server:: GET /data_request?id=lu_status2&output_format=json&DataVersion=578672005&Timeout=60&MinimumDelay=1500&_=1592671339440 HTTP/1.1 tcp{client}: 0x27493a4 2020-06-20 20:40:05.602 openLuup.server:: request completed (128491 bytes, 9 chunks, 228 ms) tcp{client}: 0x27493a4 2020-06-20 20:40:05.602 luup_log:3: ALTUI: startupDeferred, called on behalf of device:3 2020-06-20 20:40:05.606 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.Version was: v2.49b now: v2.49b #hooks:0 2020-06-20 20:40:05.649 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.DataStorageProviders was: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"default":1,"type":"number","key":"node... now: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"key":"nodeid","type":"number","default... #hooks:0 2020-06-20 20:40:05.650 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.DataStorageProviders was: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"key":"nodeid","type":"number","default... now: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"default":1,"type":"number","key":"node... #hooks:0 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.DataStorageProviders was: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"default":1,"type":"number","key":"node... now: {"emoncms":{"url":"","callback":"sendValueToStorage_emoncms","parameters":[{"default":1,"type":"number","key":"node... #hooks:0 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.VariablesToSend was: now: #hooks:0 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.RemoteVariablesToWatch was: now: #hooks:0 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.VariablesToWatch was: now: #hooks:0 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.Timers was: [] now: [] #hooks:0 2020-06-20 20:40:05.651 luup_log:3: ALTUI: Wkflow - enableWorkflows(3,0,0) 2020-06-20 20:40:05.651 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.Timers was: [] now: #hooks:0 2020-06-20 20:40:05.652 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.WorkflowsActiveState was: [] now: #hooks:0 2020-06-20 20:40:05.652 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.WorkflowsVariableBag was: now: #hooks:0 2020-06-20 20:40:05.652 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.WorkflowsActiveState was: now: [] #hooks:0 2020-06-20 20:40:05.652 luup.register_handler:: global_function_name=myALTUI_Handler, request=ALTUI_Handler 2020-06-20 20:40:05.654 luup.call_action:: 0.urn:micasaverde-com:serviceId:HomeAutomationGateway1.RunLua 2020-06-20 20:40:05.654 luup.register_handler:: global_function_name=ALTUI_LuaRunHandler, request=ALTUI_LuaRunHandler 2020-06-20 20:40:05.655 luup.call_action:: 0.urn:micasaverde-com:serviceId:HomeAutomationGateway1.RunLua 2020-06-20 20:40:05.656 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.Timers was: now: [] #hooks:0 2020-06-20 20:40:05.656 luup.variable_set:: 3.urn:upnp-org:serviceId:altui1.PendingReset was: 0 now: 0 #hooks:0 2020-06-20 20:40:05.662 luup.set_failure:: status = 0 2020-06-20 20:40:05.662 luup.variable_set:: 3.urn:micasaverde-com:serviceId:HaDevice1.CommFailure was: 0 now: 0 #hooks:0 2020-06-20 20:40:05.662 luup.variable_set:: 3.urn:micasaverde-com:serviceId:HaDevice1.CommFailureTime was: 0 now: 0 #hooks:0 2020-06-20 20:40:05.662 luup_log:3: ALTUI: startup completed 2020-06-20 20:40:05.669 openLuup.server:: GET /data_request?id=user_data&output_format=json&DataVersion=578663463&_=1592671339441 HTTP/1.1 tcp{client}: 0x27493a4 2020-06-20 20:40:05.857 openLuup.server:: request completed (179603 bytes, 12 chunks, 187 ms) tcp{client}: 0x27493a4 2020-06-20 20:40:07.905 openLuup.server:: GET /data_request?id=lu_status2&output_format=json&DataVersion=682008955&Timeout=60&MinimumDelay=1500&_=1592671339442 HTTP/1.1 tcp{client}: 0x27493a4 2020-06-20 20:40:08.014 openLuup.server:: request completed (20870 bytes, 2 chunks, 108 ms) tcp{client}: 0x27493a4 2020-06-20 20:40:08.166 openLuup.server:: GET /data_request?id=lu_status2&output_format=json&DataVersion=682008971&Timeout=60&MinimumDelay=1500&_=1592671339443 HTTP/1.1 tcp{client}: 0x27493a4 2020-06-20 20:41:08.520 openLuup.server:: request completed (363 bytes, 1 chunks, 60353 ms) tcp{client}: 0x27493a4Hit update. Showing 2.4.30 No change in the devices (I don't have an update button on the console page, but I did it from AltUI)
C
