UZB/RaZberry Firmwares - Update

[rafale77]

I would recommend running the upgrade through the z-way-server expert UI if you can. It makes things a lot simpler. Using the firmware tool works better but is a bit of a learning curve. Indeed if you open the version graph, you need to find which firmware version you currently are on and clicking on the corresponding dot on the graph opens a simple page listing all the url of every possible downgrade/firmware available from that version. This is where you get the url to use with the tool...

[parkerc]

Thanks

I downloads the software and installed the zway stuff, and then useD the ‘ExpertUI’ as described to update the firmware and boot loader; interestingly their website says the latest version is 5.39. - https://z-wave.me/support/uzbrazberry-firmwares/

Yet, It seems while I was originally only on 5.05, after two upgrades 5.06 and 5.07 - the software tells me I’m now all up to date.. yet it’s reporting I’m on 5.07..

Here’s my updated report.. ..

Device ready in:25.022865057 seconds
          FULL INFO
Openning port                            ..............................                            OK


          SERIAL INFO 
                 VERSION:  05 07  VENDOR:  01 15

          ZME_CAPABILITIES 
                     UID:  7B 93 21 D8 62 1E C2 2B 4F 6E 8B 94 A3 05 01 36 
                  VENDOR:  00 00   NODES: FF 
                   FLAGS:  05 00 00 00 00 00 00 00 00 00 00 00 00

          FIRMWARE CRC
                    BOOT:  9D 04      FW:  AE CB
          MISC 
                    FREQ:  EU 
           
                                         NVR Content
          -------------------------------------------------------------------------------------------- 
          Prog/erase lock :  FF FF FF FF FF FF FF FF, Read back lock: FF
          Rev 01, Cal 06, TXCal  17 13, SAW  FF FF FF FF, Pin FF, CRC  3E CE
          NMV: CS 15, TYPE 02, SIZE  01 00, PSIZE  01 00 (EEPROM M25PE20)
          USB: VID  FF FF, PID  FF FF, UUID  FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          -------------------------------------------------------------------------------------------- 
          FACTORY ID: WEEK 51, YEAR 16, CHIP  00 01, SER  0B D2, WS 1, HWREV: 00 01, CRC8 04

[SweetGenius]

Did you try typing all in the token field ?

[parkerc]

Hi @SweetGenius, sorry, I’m new to these modules and this whole process

What do you mean by the ‘token field’ ?
Is it the ‘Action Token’ one, shared in the screen shot above?
If so, what goes in there ?

Is this where the licensing comes in ?
Can you only go so far with the firmware upgrades ?

[rafale77]

@parkerc

On the firmware update page you should see this:

Which where you can input the "all" token so you can see all available update paths.

[parkerc]

Hi, thanks I’ve put ‘all’ in and it provided me with a list, however it still says I’m using the latest firmware ?

Also it’s a bit confusing and they mention 5.07 and 5.7 - not sure if that’s an error and they mean the same (5.07)....

[rafale77]

You should go to 5.27 as the first step. Check in the firmware map to make sure it isn't a dead end. Also you appear to have a boot loader upgrade available too but need to check whether it is a downgrade again from the firmware map.

[parkerc]

Hi @rafale77

The map is not the easiest thing to read ? - https://service.z-wave.me/expertui/uzb-stats/versions-graph.html?hw=277&with_hidden image attached is just the active ones

Am I on 5.07, or 5.7? If so, is 5.7 to 5.27 not a downgrade, rather than an upgrade ? The command line firmware tool seems to suggest I‘m on 5.07. How do you read it to work out the bootloader? I can’t see the 7278 mention via the expert Ui?

[rafale77]

5.07 = 5.7, it would be called 5.70 which doesn't exist.
Also you should try clicking the "all" map which corresponds to the "all" token in the z-way server. Once you find the bootloader and firmware version you are currently running, the map shows you to to get to where you want to go. It's actually pretty intuitive once you get the hang of it. On this map for example you can see that 5.7/40196 appears to be a dead end (have to check the all map to see the whole thing)

[parkerc]

Ok, clicking on UZB all and then 5.7, it gives me the following..

The second one relates to the bootloader upgrade option that’s presented.. is it suggesting I update the bootloader first ?

{"data":[{"id":"252","baseid":"","enabled":"enabled","type":"bootloader","file":"bin","vendorID":"277","bootloaderCRC":null,"appVersionMajor":"5","appVersionMinor":"7","targetBootloaderCRC":"40196","targetAppVersionMajor":null,"targetAppVersionMinor":null,"fileURL":"UPD_BOOTLOADER_UZB_ZME_05_07_04000001_9d04.bin","released":"2018-01-12","comment":"Update bootloader to 9d04","position":"70","version":"5.7"},

{"id":"98","baseid":"","enabled":"disabled","type":"bootloader","file":"bin","vendorID":"277","bootloaderCRC":null,"appVersionMajor":"5","appVersionMinor":"7","targetBootloaderCRC":"29304","targetAppVersionMajor":null,"targetAppVersionMinor":null,"fileURL":"bootloader_UZB_from_05_07_to_7278_2MB.bin","released":"2017-05-12","comment":"Update bootloader to 7278","position":"72","version":"5.7"},

{"id":"88","baseid":"","enabled":"disabled","type":"firmware","file":"bin","vendorID":"277","bootloaderCRC":null,"appVersionMajor":"5","appVersionMinor":"7","targetBootloaderCRC":null,"targetAppVersionMajor":"5","targetAppVersionMinor":"7","fileURL":"UPD_FIRMWARE_UZB500_X_from05_07_to_UZB500_3CH_05_07.bin","released":"2017-04-18","comment":"Update firmware to 3 channels (JP/TW/KR/SG) on 5.07","position":"57","version":"5.7"},

{"id":"89","baseid":"","enabled":"disabled","type":"firmware","file":"bin","vendorID":"277","bootloaderCRC":null,"appVersionMajor":"5","appVersionMinor":"7","targetBootloaderCRC":null,"targetAppVersionMajor":"5","targetAppVersionMinor":"7","fileURL":"UPD_FIRMWARE_UZB500_3CH_X_from05_07_to_UZB500_05_07.bin","released":"2017-04-18","comment":"Update firmware to 2 channels (EU/RU/US/ANZ/MY/IL/..) on 05.07","position":"58","version":"5.7"}]}

[rafale77]

I went to read the map myself and here are the steps I would take:
5.7 -> 5.7 40196 BL -> 5.27 ->5.36 ->5.39

So yes Bootloader first in general but need to read the version.

Also there is a hex to dec you need to do to understand the numbering. 7278 is 29304 and is likely a bootloader downgrade. You need to know what version of bootloader you are on right now.

[parkerc]

Using the control ‘Show Controller Data’ option, it looks like my bootloader is 40196

So based on your recommendation I would do the following..

Update bootloader to 7278
Update firmware to 5.25
Update firmware to 5.36
Update firmware to 5.39

[parkerc]

Just to confused matters,

I’ve upgraded the bootloader to 7278, and the information in the system has changed to 29304

And I’m now presented with another bootloader option..

This time.. 9d04 , which hex to Dec = 40196 - which means I downgraded the bootloader ?

This is turning out to be far more complicated than I thought - I had hoped the expert UI would guide me through the required sequence so I have the latest version .

So now we have 5.22 and 5.23 added In to the mix ?

Sorry for all the questions

[rafale77]

So indeed as I said 7278 seems to be a downgrade. I wouldn’t have run the boot loader update knowing that my boot loader number was already higher. Sorry for not being clear. You indeed need to be on 40196 and then move on from there as I described from my previous post.

[parkerc]

Thanks for all the guidance @rafale77

I’ve reapplied the bootloader update, and have started to go through the incremental firmware updates..

Update : What’s interesting is after going to 5.25, it gives me two sideways options of ‘normal’ and ‘bridge’ version ?

Assuming it’s knows what it’s doing - and to try to keep moving on, after going to 5.26, (which admittedly was not in our earlier list), I now have the following options .

Trying to work out the correct path to take (factoring what ‘active; and what not) is a puzzle in itself_

All..
Active ..

Looking at the published firmware releases, is that the path I ultimate want to take ?

So, that would suggest 5.27 firmware (not bridge) next - rather than 5.33 ? (Any idea why there are all duplicates ?)

[rafale77]

You didn't need to go to 5.26. As you can see from the graph, 5.27 is kind of a central version from which they build many upgrades from so it is the pivotal version. I only use the static versions of the firmware.
5.33 is a dead end. Don't go there.

[parkerc]

@rafale77 said in UZB/RaZberry Firmwares - Update:

You didn't need to go to 5.26.

I didn’t seem to have any other option, (based on the earlier screenshot) all I could do was upgrade from 5.25 to 5.26. But now I’m on 5.26, I do have the 5.27 option..

[rafale77]

ha... such a complicated scheme... it really didn't need to do so. But anyway, once you get to 5.27 you can practically go anywhere you need.

[parkerc]

Hi @rafale77, seems I’ve reached another block, trying to move from 5.26 to 5.27

And now over 3,600 items appeared in the queue..

I’ve tried a couple of times , same result..

[rafale77]

Yeah there where I switched to the command line tool. Do you already have devices on that stick? @poltoS says it is because the upgrade process is interrupted by RF signals. I thought it was due to some EEPROM start location issues but I did find it painful in recent versions to upgrade and had to retry dozens of times to get it through. It looks like the upload of the firmware started but gets interrupted by something.